Panasonic PT-LB386 - Page 133

ENGLISH - 133
Mode
Display resolution
(dots)
Scanning frequency
Dot clock
frequency
(MHz)
Format
PnP*
1
H (kHz) V (Hz) COMPUTER HDMI
1280 x 720/50 1 280 x 720 37.1 49.8 60.5 R/H -- --
1280 x 720/60 1 280 x 720 44.8 59.9 74.5 R/H -- --
1280 x 768/60 1 280 x 768 47.8 59.9 79.5 R/H -- --
1280 x 768/75 1 280 x 768 60.3 74.9 102.3 R/H -- --
1280 x 768/85 1 280 x 768 68.6 84.8 117.5 R/H -- --
1280 x 800/50 1 280 x 800 41.3 50.0 68.0 R/H -- --
1280 x 800/60 1 280 x 800 49.7 59.8 83.5 R/H
l
*5
l
*5
1280 x 800/75 1 280 x 800 62.8 74.9 106.5 R/H -- --
1280 x 800/85 1 280 x 800 71.6 84.9 122.5 R/H -- --
1280 x 960/60 1 280 x 960 60.0 60.0 108.0 R/H -- --
1280 x 1024/60 1 280 x 1 024 64.0 60.0 108.0 R/H -- --
1280 x 1024/75 1 280 x 1 024 80.0 75.0 135.0 R/H -- --
1280 x 1024/85 1 280 x 1 024 91.1 85.0 157.5 R/H -- --
1366 x 768/50 1 366 x 768 39.6 49.9 69.0 R/H -- --
1366 x 768/60 1 366 x 768 47.7 59.8 85.5 R/H -- --
1400 x 1050/60 1 400 x 1 050 65.3 60.0 121.8 R/H -- --
1400 x 1050/60 1 400 x 1 050 65.2 60.0 122.6 R/H -- --
1400 x 1050/75 1 400 x 1 050 82.3 74.9 156.0 R/H -- --
1440 x 900/60 1 440 x 900 55.9 59.9 106.5 R/H -- --
1600 x 900/50 1 600 x 900 46.3 50.0 97.0 R/H -- --
1600 x 900/60 1 600 x 900 55.9 60.0 119.0 R/H -- --
1600 x 1200/60 1 600 x 1 200 75.0 60.0 162.0 R/H
l l
1680 x 1050/50 1 680 x 1 050 54.1 50.0 119.5 R/H -- --
1680 x 1050/60 1 680 x 1 050 65.3 60.0 146.3 R/H -- --
1920 x 1080/50 1 920 x 1 080 55.6 49.9 141.5 R/H -- --
1920 x 1080/60
*4
1 920 x 1 080 66.6 59.9 138.5 R/H -- --
1920 x 1200/50 1 920 x 1 200 61.8 49.9 158.3 R/H -- --
1920 x 1200/60
*4
1 920 x 1 200 74.0 60.0 154.0 R/H -- --
*1 Where marked "l" signals indicates in Plug and Play is compatible with EDID of projector. Unmarked signals in Plug and Play may also
be compliant if input terminals are written in the format list. Where Plug and Play is unmarked and nothing is written in the format list,
di󰀩culties in projecting image may occur even when computer and projector appear to have same resolution.
*2 Pixel-Repetition signal (dot clock frequency 27.0 MHz) only.
*3 When a 1125 (1035)/60i signal was input, it is displayed as a 1125 (1080)/60i signal.
*4 VESA CVT-RB (Reduced Blanking)-compliant.
*5 Only for PT-LW376 and PT-LW336.
*6 The signal with 1/1.001x vertical scanning frequency is also supported.
Note
f The number of display dots is 1 280 x 800 for the PT-LW376 and PT-LW336 and 1 024 x 768 for the PT-LB426, PT-LB386 , PT-LB356 and
PT-LB306.
A signal with a di󰀨erent resolution will be projected after converting the resolution to match the projector display.
f “i” added to the resolution value indicates an interlaced signal.
f When interlaced signals are connected, icker may occur on the projected image.
f The image may not be displayed in full screen according to the computer output setting.
Chapter 7 Appendix - Technical Information