Panasonic PT-RQ32K - Page 258

Chapter 7 Appendix — Technical information
258 - ENGLISH
List of simultaneous input compatible signals
The following table species the simultaneous input compatible video signals that the projector can project.
Signal name
(SIGNAL FORMAT)
Resolution
(Dots)
Scanning freq.
Dot clock freq.
(MHz)
Simultaneous input compatible signal
Horizontal
(kHz)
Vertical
(Hz)
SDI
*1
HDMI
*2
DVI-D
*3
Double
speed
Quadruple
speed
Double
speed
Quadruple
speed
Double
speed
Quadruple
speed
1080/60p 1 920 x 1 080 67.5 60.0 148.5
l l l l l l
1080/50p 1 920 x 1 080 56.3 50.0 148.5
l l l l l l
1366 x 768/50 1 366 x 768 39.6 49.9 69.0 ― ―
l
―
l
―
1366 x 768/60 1 366 x 768 47.7 59.8 85.5 ― ―
l
―
l
―
1400 x 1050/50 1 400 x 1 050 54.1 50.0 99.9 ― ―
l
―
l
―
1400 x 1050/60 1 400 x 1 050 65.3 60.0 121.8 ― ―
l
―
l
―
1920 x 1080/50 1 920 x 1 080 55.6 49.9 141.5 ― ―
l
―
l
―
1920 x 1080/60 1 920 x 1 080
*4
66.6 59.9 138.5 ― ―
l
―
l
―
1920 x 1200/50 1 920 x 1 200 61.8 49.9 158.3 ― ―
l
―
l
―
1920 x 1200/60RB 1 920 x 1 200
*4
74.0 60.0 154.0 ― ―
l
―
l
―
3840 x 2160/60 3 840 x 2 160 135.0 60.0 594.0 ― ―
l
*5
― ― ―
3840 x 2160/50 3 840 x 2 160 112.5 50.0 594.0 ― ―
l
*5
― ― ―
4096 x 2160/60 4 096 x 2 160 135.0 60.0 594.0 ― ―
l
*5
― ― ―
4096 x 2160/50 4 096 x 2 160 112.5 50.0 594.0 ― ―
l
*5
― ― ―
*1 In addition to the standard SDI input, this supports the input from the optional 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G) installed
in the slot.
*2 This is supported when the optional Interface Board for HDMI 2 input (Model No.: ET-MDNHM10) is installed in the slot.
*3 This is supported when the optional Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10) is installed in the slot.
*4 VESA CVT-RB (Reduced Blanking) compliant
*5 When performing the simultaneous input of the 4K image (resolution of 3 840 x 2 160 or 4 096 x 2 160) using the Interface Board for HDMI 2 input
(Model No.: ET-MDNHM10), it is necessary for the rmware version of the Interface Board for HDMI 2 input to be 2.00 or later. If the version is
earlier than 2.00, the simultaneous process is not performed even if corresponding signal is input. Consult your dealer regarding the version update
to the latest rmware.
For details on how to conrm the rmware version, refer to “How to conrm the rmware version of the Interface Board (optional)” (x page 33).
Note
f The geometric adjustment function and the expansion function by applying the optional Upgrade Kit (Model No.: ET-UK20) cannot be used
when the video signal in simultaneous format is input.