64
Others
SXGA
:
1 280 or more, less than 1 600
UXGA
:
1 600 or more, less than 2 048
QXGA
:
2 048 or more
(White):
Photoshot Mode
(Red):
While Photoshot recording is activated
(Green):
While the Card being read
(Red):
Using the card that cannot be
recognized
To Display Date/Time Indication
This switches between date and time indications.
Set [ BASIC] or [ ADVANCE] >> [ DATE/TIME]
>> [D/T], [DATE] or [OFF]. (pp. 22, 23, 24)
• The Camcorder automatically records the date and
time of picture taking on the tape.
• You can also show or change the Date/Time
Indication by repeatedly pressing the [DATE/TIME]
Button on the Remote Control (PV-GS35 only).
To Change the Display Mode
Set [ SETUP] >> [ DISPLAY] >> [ON] or [OFF].
Set to [ON] and the display mode can be switched to
all functions. Set to [OFF] and it can be switched to
minimum display. (pp. 23, 24)
Progressive Photoshot
You cannot use the Progressive Photoshot Function in
the following cases.
When using Tape Recording Mode
• Digital Zoom [ ]
• 1/750 s or faster shutter speed
• When brightness is insufficient
• When the MagicPix Function is ON
• When the Portrait is used
• When the Gain Up mode is set to ON
When using Card Recording Mode
• When brightness is insufficient
• When the Gain Up mode is set to ON
Initializing the Modes
You can change the Menu settings back to the
shipping condition.
• Set to Tape/Card Recording Mode.
1 Set [ ADVANCE] >> [ INITIAL SET] >>
[YES].
• The initializing takes a little while.
• Initializing will not erase a clock setting (p. 24) that
has been adjusted.
Warning/Alarm Indications
If any one of the following indications lights up or
flashes, please check the Camcorder.
Confirmatory Indications
:
A cassette with the accidental erasure
prevention slider placed in the [SAVE]
position is inserted.
No cassette is inserted.
[--] /
:
The built-in battery is low. (p. 24)
:
The Warning/Alarm Indication appears
when you record yourself. Turn the LCD
Monitor towards the Viewfinder and check
the Warning/Alarm Indication.
:
No card is inserted.
REMOTE: An incorrect Remote Control mode has
been selected. (p. 15)
END :
The tape came to the end during
recording.
:
The video heads are dirty. (pp. 71~72)
Textual Indications
DEW DETECT/ EJECT TAPE:
Condensation has occurred. Take out the
cassette and wait for a while. It takes some time
until the cassette holder opens, but this is not a
malfunction. (p. 71)
TAPE END:
The tape came to
the end during recording.
NEED HEAD CLEANING:
The video heads are dirty. (pp. 71~72)
PUSH THE RESET SWITCH:
An irregularity in the equipment has been
detected. Press the [RESET] Button (p. 77). This
may solve the problem.
LOW BATTERY:
The Battery is low. Recharge it. (p. 15)
NO TAPE:
No tape is inserted. (p. 17)
CHECK REMOTE MODE:
An incorrect Remote Control Mode has
been selected. This is only displayed at the
first operation of the Remote Control after
powering-on. (p. 15)
CHECK REC TAB:
You are attempting to record pictures on a tape
with the accidental erasure prevention slider
placed in the [SAVE] position.
You are attempting Audio Dubbing or Digital
Dubbing on a tape with the accidental erasure
prevention slider placed in the [SAVE] position.
WRONG TAPE FORMAT:
You are attempting to play back a tape section
that has been recorded with a different TV
system.
This cassette is incompatible.
To Next Page
Loading...
