Panasonic Ramsa WR-S4424 - Page 6

_
Le
12-point LED Bar-graph Meters
(1/2/3/4/L/R)
These LED peak reading meters are designed to have
quick attack time to monitor transients and slow decay
time for optimum visual indication. There are 3 colour
ranges, along with dB graduations relative to nominal
level: Green for —20 dB to 0 dB, Yellow for +1 dB to +5
dB, Red for +8 dB or more.
: This meter displays Group 1 output level or AUX 1
output level. ‘
: This meter displays Group 2 output level or AUX 2
output level.
: This meter displays Group 3 output level or AUX 3
output level.
: This meter displays Group 4 output level or AUX 4
output level.
This meter displays Left Master output level.
R/PFL :
This meter displays Right Master output level or PFL
level. Meters 1-4 are switch selectable. The R/PFL
meter is automatically switched any time a PFL button
is pressed,
Power Indicator LED
This LED lights when the Power Switch is turned on.
PFL Indicator LED (R/PFL)
This LED lights when any PFL Switch is turned on.
The R/PFL. 12-point LED bar-graph meter displays PFL
signal level when this LED is lit.
Meter Selection Switches
(METER SELECT, 1/2/3/4)
These switches are used to select either Group or
AUX bus signals to be displayed by the 12-point LED
bar-graph meters 1-4.
Pressing the switch down selects the AUX signal. The
up position selects Group.
AUX Return Assign Switches
These switches route the stereo AUX Return signals to
the group and master busses. The left input signal can
be sent to Group 1, Group 3, and L Master. The right
input signal can be sent to Group 2, Group 4, and R
Master.
For more information regarding connection of AUX
Return signals, see number 3-1 on page 8, "AUX Return
Input Jacks”.
Talk Back Assign Switches
These route the signal input via the TB Mic connector.
The talk back signal is assignable to all group, master,
and AUX busses.
. Talk Back Microphone Connector (T.B MIC)
This XLR female connector is used for the connection
of a talk back microphone.
. Talk Back Level Control
This is a dual-function control to simultaneously adjust
the talk back input sensitivity and the output level of
the talk back signal.
10.
11.
12.
13.
14,
15,
16.
17.
18.
19.
20.
21.
Tatk Back ON/OFF Switch (ON)
This is a push-push type switch. The Talkback function
is active while the switch is held in the down position.
Balance Controls (BAL, L-R)
These controls set the balance between the Left and
Right AUX RTN input signals.
AUX Return Input Controls (RTN 1/2/3/4, 0-10)
These controls set the level of Stereo AUX Return input
signal to be sent to the assigned busses.
Phone Jack (PHONES)
1/4” TRS phone jack for headphone.
Maximum output is 160 mW / 400 ohms.
Monitor Master Level Control (MONI, 0-10)
This control adjusts the level of the monitor outputs.
The takeoff point for the monitor signal is either L/R
Master or PFL. When any PFL button is depressed, it
takes priority over the L/R Master for being sent to the
Monitor and Headphone Outputs. Therefore, any buss
can be monitored, as well as any input channel.
Mono Monitor Switch (MONO)
Pressing this switch down to the mono position
combines the left and right monitor into a mono signal,
then sends it to the left and right Monitor outputs.
Headphone Level Control (PHONES, 0-10)
This control is used to set the headphone level. The
signal sent to the headphone output is the same as the
one being sent to the monitor outputs (L/R Master or
PFL).
PFL Control (PFL 0-10)
This control adjusts the level of the PFL signal present .
at the monitor outputs and headphone outputs. Proper
setting of this control avoids variances in level when
switching between Master and PFL mode.
Group L-R Send Switches (L-R)
When these switches are turned on, the Group signal
is sent to the L/R Master busses. This is useful for
creating a submix.
AUX 1-4 Master Level Controls (AUX, 0-10)
These controls ‘adjust the overall level of each AUX
output signal.
Group Pan Pot Controls (PAN, L-R) |
These controls are used to adjust the left/right balance
of the Group signal sent to the Master L and R channels
via the L/R Send switches.
Channel On Switches (ON)
These are the on/off switches for the Group and
Master Outputs.
Pre Fader Listening Switches (PFL)
These switches may be pressed to send any of the
Group, AUX, or Master busses to the Monitor and
Headphone Outputs. The PFL signal takes priority over
the L/R Master monitor signal.