8
RQT7619
INTRO
STEP 2
Set up to match your television and remote control
You do not have to change the setting when connected to a 4:3
standard aspect television that is not compatible with progressive
output (➡ page 45).
1 Press [FUNCTIONS].
2 Press [3, 4] to select “SETUP” and
press [ENTER].
3
Press [
3
,
4
] to select “TV Screen” and press [
1
].
4 Press [3, 4] to select “TV Type” and
press [ENTER].
≥Aspect 4:3/Aspect 16:9:
≥480P/480I:
Select “480P” if the television is compatible with
progressive output.
5
Press [
3
,
4
] to select the item and press [ENTER].
You can configure the remote control TV operation buttons to turn
the television on/off, change the television input mode, select the
television channel and change the television volume.
1
Switch [HOME THEATER, TV] to “TV”.
2 Point the remote control at the television
While pressing [Í POWER], enter
the code with the numbered buttons.
e.g., 01: [0] ➡ [1]
Manufacturer and Code No.
Test by turning on the television and changing channels. Repeat
the procedure until you find the code that allows correct operation.
≥If your television brand is not listed or if the code listed for your
television does not allow control of your television, this remote
control is not compatible with your television.
Change the remote control code on the main unit and the remote control
(the two must match) if you place other Panasonic products close together.
Use “1”, the factory set code, under normal circumstances.
1 Press [FUNCTIONS].
2 Press [3, 4] to select “SETUP” and
press [ENTER].
3
Press [
3
,
4
] to select “Set Up” and press [
1
].
4 Press [3, 4] to select “Remote
Control Code” and press [ENTER].
5 Press [3, 4] to select the code (1, 2,
or 3) and press [ENTER].
6 To change the code on the remote control
While pressing [ENTER], press and
hold the numbered button ([1], [2] or
[3]) for more than 2 seconds.
7 Press [ENTER].
∫
When the following indicator appears on the unit’s display
Change the code on the remote control to match the main unit’s (
➡
step 6).
To exit the screen
Press [RETURN] several times.
To return to the previous screen
Press [RETURN].
Selecting television type
4:3 standard aspect television
16:9 widescreen television
CH
VOLUME
SKIP
STOP PAUSE PLAY/x1.3
SLOW/SEARCH
CANCEL
123
4
5
6
789
0
HOME THEATER TV
Info
MULTI REAR
DUBBING
S.POSITION
CHAPTER
C.FOCUS
AUDIO
CH SELECT
RETURN
ERASE
REC MODE
TIME SLIP
L1/OPT
TOP MENU
ENTER
DIRECT NAVIGATOR
FUNCTIONS
MIX
2CH
REC
TEST
CM SKIP
REPEAT
MUTING
S W. LEVEL
TV/VIDEO
AUXFM/AMDVDHDD
DISPLAY
POWER
PRO LOGIC
SHIFT
HDD/DVD
INPUT
PA G E
VCR Plus+
FM MODE
SUB MENU
STATUS
EQ/SFC
PROG/CHECK
TV GUIDE
CH
VOLUME
SKIP
STOP PAUSE PLAY/x1.3
SLOW/SEARCH
CANCEL
123
5
6
789
0
HOME THEATER TV
Info
MULTI REAR
DUBBING
S.POSITION
CHAPTER
C.FOCUS
AUDIO
CH SELECT
RETURN
ERASE
REC MODE
TIME SLIP
L1/OPT
TOP MENU
ENTER
DIRECT NAVIGATOR
FUNCTIONS
MIX
2CH
REC
TEST
CM SKIP
REPEAT
MUTING
S W. LEVEL
TV/VIDEO
AUXFM/AMDVDHDD
DISPLAY
POWER
PRO LOGIC
SHIFT
HDD/DVD
INPUT
PA G E
FM MODE
SUB MENU
STATUS
EQ/SFC
PROG/CHECK
TV GUIDE
4
VCR Plus+
3 4 2 1
ENTER
RETURN
HOME
THEATER,TV
TV/VIDEO
W X CH
r s VOLUME
FUNCTIONS
Í POWER
Numbered
buttons
SETUP
Set Up
Disc
Video
Audio
Display
TV Type
Aspect 4:3 & 480I
Aspect 4:3 & 480P
TV Screen
Channel
Aspect 16:9 & 480P
Aspect 16:9 & 480I
4:3 16:9
Television operation
Panasonic
National
QUASAR
01, 02
PHILIPS (RC-5) 03
RCA 05
SAMSUNG 14, 18, 19
FISHER 10 SANYO 10
GE 05 SHARP 06, 07
GOLDSTAR 15, 16, 17 SONY 08
HITACHI 12 SYLVANIA 03
JVC 11 THOMSON 05
LG 15, 16, 17 TOSHIBA 09
MAGNAVOX 03 ZENITH 04
MITSUBISHI 13
When other Panasonic products
respond to this remote control
SETUP
Disc
Remote Control Code
Channel
Set Up
Press
“
±
”
and
“
ENTER
”
together
for more than 2 seconds on the remote.
The unit’s remote control code
7619en.book 8 ページ ２００４年５月６日 木曜日 午前９時３３分
To Next Page
Loading...
