Panasonic WV-SC588A - Installations;Connections

Installations/Connections
Before installation, prepare the following
There are 4 methods to install the camera to a ceiling or wall as described below. Prepare the required devices and cables
for each installation method before starting the installation.
<Installing the camera to a ceiling that has adequate structural strength>
Use the camera mount bracket (accessory).
 • Procure4screws(M4)tosecurethecameramountbracket(accessory).
 • Selectscrewsaccordingtothematerialoftheceilingthatthecamerawillbemountedto.
 • Theminimumrequiredpull-outcapacityofasinglescrewis196N{44lbf}ormore.
 • Whenmountingthecameraonaconcreteceiling,useanAYplugbolt(M4)forsecuring.
(Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
<Installing the camera to a ceiling that has inadequate structural strength such as plaster board ceiling>
The area of the ceiling that the camera will be installed to must be sufficiently reinforced, or the optional ceiling mount
bracket for the camera (WV-Q105, weight approx. 0.15 kg {0.33 lbs}) must be used.
 • Whenusingtheceilingmountbracket(WV-Q105),prepare2anchorbolts(M10)tosecurethebrackettoaroofspace
(including 1 for securing the safety wire).
 • Theminimumrequiredpull-outcapacityofasinglescreworanchorboltis5timesormoreofthetotalweightofthe
camera and all of its parts.
 • Existinganchorboltscanbeusedtosecurethesafetywiretoaceiling.Ifexistinganchorboltsareused,theremaynot
be enough supplied nuts to be used with all the anchor bolts. In this case, procure the required nuts separately.
<Installing the camera embedded to a ceiling that has inadequate structural strength such as plaster board ceiling>
The area of the ceiling that the camera will be installed to must be sufficiently reinforced, or the optional ceiling embedding
bracket for the camera (WV-Q126A, weight approx. 1.2 kg {2.65 lbs}) must be used.
 • Whenusingtheceilingembeddingbracket(WV-Q126A),prepare2anchorbolts(M10)tosecurethebrackettoaroof
space (including 1 for securing the safety wire).
 • Theminimumrequiredpull-outcapacityofasinglescreworanchorboltis5timesormoreofthetotalweightofthe
camera and all of its parts.
 • Existinganchorboltscanbeusedtosecurethesafetywiretoaceiling.Ifexistinganchorboltsareused,theremaynot
be enough supplied nuts to be used with all the anchor bolts. In this case, procure the required nuts separately.
<Installing the camera to a wall>
Use the wall mount bracket (WV-Q119, weight approx. 0.65 kg {1.43 lbs}).
 • Procure4screws(M4)tosecurethewallmountbracket(WV-Q119)tothewall.
 • Selectscrewsaccordingtothematerialofthewallthatthecamerawillbemountedto.
 • Theminimumrequiredpull-outcapacityofasinglescreworanchorboltis196N{44lbf}ormore.
When installing the camera using the ceiling mount bracket, the ceiling embedding bracket, or the wall mount bracket,
refer to the instructions included with those optional accessories.
Caution:
 • AREADILYACCESSIBLEDISCONNECTDEVICESHALLBEINCORPORATEDTOTHEEQUIPMENTPOWEREDBY
12VDC POWER SUPPLY.
 • ONLYCONNECT12VDCCLASS2POWERSUPPLY(UL1310/CSA223)orLIMITEDPOWERSOURCE(IEC/EN/
UL/CSA 60950-1).
17