14-6 Serial Communications
590 Series DC Digital Converter
..........ADAPTION
............MODE [268 ] = 0
............SPD BRK1 (LOW) [269 ] = 1.00 %
............SPD BRK2 (HIGH) [270 ] = 5.00 %
............PROP. GAIN [271 ] = 5.00
............INT. TIME CONST. [272 ] = 0.500 SECS
..........I GAIN IN RAMP [274 ] = 1.0000
..........POS. LOOP P GAIN [273 ] = 0.00 %
..........ZERO SPD. QUENCH
............ZERO SPD. LEVEL [284 ] = 0.50 %
............ZERO IAD LEVEL [285 ] = 1.50 %
........SETPOINTS
..........SETPOINT 1 [289 ] = 0.00 %
..........SIGN 2 (A3) [9 ] = POSITIVE
..........RATIO 2 (A3) [7 ] = 1.0000
..........SETPOINT 2 (A3) [290 ] = 0.00 %
..........SETPOINT 3 [291 ] = 0.00 %
..........SETPOINT 4 [41 ] = 0.00 %
..........MAX DEMAND [357 ] = 105.00 %
..........MIN DEMAND [358 ] = -105.00 %
......STANDSTILL
........STANDSTILL LOGIC [11 ] = DISABLED
........ZERO THRESHOLD [12 ] = 2.00 %
........SOURCE TAG [306 ] = 89
......SETPOINT SUM 1
........RATIO 1 [6 ] = 1.0000
........RATIO 0 [208 ] = 1.0000
........SIGN 1 [8 ] = POSITIVE
........SIGN 0 [292 ] = POSITIVE
........DIVIDER 1 [419 ] = 1.0000
........DIVIDER 0 [420 ] = 1.0000
........DEADBAND WIDTH [131 ] = 0.0 %
........LIMIT [375 ] = 105.00 %
........INPUT 2 [423 ] = 0.00 %
........INPUT 1 [100 ] = 0.00 %
........INPUT 0 [309 ] = 0.00 %
....PASSWORD
......ENTER PASSWORD [120 ] = 0x0000
......CHANGE PASSWORD [121 ] = 0x0000
....ALARM STATUS
......HEALTH WORD [115 ] = 0x0210
......HEALTH STORE [116 ] = 0x0000
....MENUS
......FULL MENUS [37 ] = ENABLED
......MENU DELAY [38 ] = 31 *
......LANGUAGE
....PARAMETER SAVE
....SERIAL LINKS
......MAIN PORT (P1)
........SRL LINK ENABLE [146 ] = ENABLED
........GROUP ID (GID) [138 ] = 0
........UNIT ID (UID) [139 ] = 0
........PROTOCOL [148 ] = EI ASCII
........BAUD RATE [150 ] = 9600
........ESP SUP. (ASCII) [152 ] = DISABLED
........CHANGEBAND (BIN) [144 ] = 0.00 %
........ERROR REPORT [158 ] = 0x00C0
........PNO. 7 [142 ] = 0xFFFF
........OPTION ADDRESS [499 ] = 0
........OPTION VERSION [303 ] = 0.00
........PARITY [334 ] = EVEN
......AUX PORT (P2)
........SRL LINK ENABLE [147 ] = ENABLED
........GROUP ID (GID) [140 ] = 0
........UNIT ID (UID) [141 ] = 0
........PROTOCOL [149 ] = EI ASCII
........BAUD RATE [151 ] = 9600
........ESP SUP. (ASCII) [153 ] = DISABLED
........CHANGEBAND (BIN) [145 ] = 0.00 %
........ERROR REPORT [159 ] = 0x00C0
........PNO. 7 [143 ] = 0xFFFF
......SYSTEM PORT (P3)
........P3 SETUP
..........MODE [130 ] = DISABLED
..........5703 SUPPORT
............SETPT. RATIO [132 ] = 0.0000
............SETPT. SIGN [133 ] = POSITIVE
............5703 INPUT [187 ] = 0.00 %
............5703 OUTPUT [189 ] = 0.00 %
..........BISYNCH SUPPORT
............GROUP ID (GID) [329 ] = 0
............UNIT ID (UID) [330 ] = 0
............ESP SUP. (ASCII) [328 ] = DISABLED
............CHANGEBAND (BIN) [331 ] = 0.00 %
............ERROR REPORT [332 ] = 0x00C0
............PNO. 7 [333 ] = 0xFFFF
..........P3 BAUD RATE [198 ] = 9600
........DUMP MMI -> P3
........UDP XFER <- P3
........UDP XFER -> P3
......PNO CONFIG
........PNO 112 [312 ] = 354 *
........PNO 113 [313 ] = 22 *
........PNO 114 [314 ] = 209 *
........PNO 115 [315 ] = 18 *
........PNO 116 [316 ] = 170 *
........PNO 117 [317 ] = 19 *
........PNO 118 [318 ] = 174 *
........PNO 119 [319 ] = 47 *
........PNO 120 [320 ] = 304 *
........PNO 121 [321 ] = 32 *
........PNO 122 [322 ] = 33 *
........PNO 123 [323 ] = 31 *
........PNO 124 [324 ] = 24 *
........PNO 125 [325 ] = 49 *
........PNO 126 [326 ] = 201 *
........PNO 127 [327 ] = 210 *
....SYSTEM
......SOFTWARE
......CONFIGURE I/O
........CONFIGURE ENABLE [39 ] = DISABLED
........ANALOG INPUTS
..........ANIN 1 (A2)
............CALIBRATION [230 ] = 1.0000
............MAX VALUE [231 ] = 100.00 %
............MIN VALUE [232 ] = -100.00 %
............DESTINATION TAG [246 ] = 100
..........ANIN 2 (A3)
............CALIBRATION [233 ] = 1.0000
............MAX VALUE [234 ] = 100.00 %
............MIN VALUE [235 ] = -100.00 %
..........ANIN 3 (A4)
............CALIBRATION [236 ] = 1.0000
............MAX VALUE [237 ] = 100.00 %
............MIN VALUE [238 ] = -100.00 %
............DESTINATION TAG [249 ] = 5
..........ANIN 4 (A5)
............CALIBRATION [239 ] = 1.0000
............MAX VALUE [240 ] = 100.00 %
............MIN VALUE [241 ] = -100.00 %
............DESTINATION TAG [250 ] = 48
..........ANIN 5 (A6)
............CALIBRATION [242 ] = 1.0000
............MAX VALUE [243 ] = 100.00 %
............MIN VALUE [244 ] = -100.00 %
............DESTINATION TAG [247 ] = 301
........ANALOG OUTPUTS
..........ANOUT 1 (A7)
............% TO GET 10V [245 ] = 100.00 %
............MODULUS [362 ] = FALSE
............OFFSET [464 ] = 0.00 %
............SOURCE TAG [251 ] = 62
..........ANOUT 2 (A8)
............% TO GET 10V [248 ] = 100.00 %
............MODULUS [363 ] = FALSE
............OFFSET [465 ] = 0.00 %
............SOURCE TAG [252 ] = 63
........DIGITAL INPUTS
..........DIGITAL INPUT C4
............DESTINATION TAG [494 ] = 496
..........DIGITAL INPUT C5
............DESTINATION TAG [495 ] = 497
..........DIGIN 1 (C6)
............VALUE FOR TRUE [103 ] = 0.01 %
............VALUE FOR FALSE [104 ] = 0.00 %
............DESTINATION TAG [102 ] = 90
..........DIGIN 2 (C7)
............VALUE FOR TRUE [106 ] = 0.01 %
............VALUE FOR FALSE [107 ] = 0.00 %
............DESTINATION TAG [105 ] = 118
..........DIGIN 3 (C8)
............VALUE FOR TRUE [109 ] = 0.01 %
............VALUE FOR FALSE [110 ] = 0.00 %
............DESTINATION TAG [108 ] = 119
........DIGITAL OUTPUTS
..........DIGOUT 1 (B5)
............THRESHOLD (>) [195 ] = 0.00 %
............MODULUS [43 ] = TRUE
To Next Page
Loading...
