Bulletin TI-FID1000C FID 1000 and 2500 Gas Stations
Parker Hannifin Corporation
Filtration and Separation Division
Haverhill, MA • 1-800-343-4048
www.parker.com/ags
20
System Specifications, Parts, Accesssories
System Specifications
FID 1000 FID 2500
Hydrogen Purity 99.9995% 99.9995%
ZAG Purity <0.1 ppm Methane in Air Challenge <0.1 ppm Methane in Air Challenge
CSA Certification Standard CAN/CSA C22.2 No 1010.1-92 CAN/CSA C22.2 No 1010.1-92
IEC Certification Standard IEC 1010/EN61010-1 IEC 1010/EN61010-1
IEC 1010 Installation Category Category 11 Category 11
IEC 1010 Pollution Degree Degree 2 Degree 2
UL Safety Standard UL 3101-1, First Edition UL 3101-1, First Edition
EMC Compliance CISPR11:EN55011:1991/EN50082-1:1992 CISPR11:EN55011:1991/EN50082-1:1992
Maximum Flow rate 1000cc/min (ZAG) 2500 cc/min (ZAG)
90cc/min (H2) 250 cc/min (H2)
Total Hydrocarbon Concentration < 0.1 ppm < 0.05 ppm
Max Inlet Hydrocarbon Concentration 100 ppm 100 ppm
Pressure Drop at Max. Flow rate < 5 psid (0.3 bar ) < 5 psid (0.3 bar )
Outlet Air Temperature ambient + 20°F (+ 11°C) ambient + 20°F (+ 11°C)
Discharge Pressure 0-90 psig ( 0-6.2 barg ) 0-90 psig ( 0-6.2 barg )
Hydrogen Outlet Port 1/8" compression, SS 1/8" compression, SS
ZAG Outlet Port 1/8" compression, Brass 1/8" compression, Brass
Hydrogen Relief Port 1/4" Female NPT 1/4" Female NPT
Compressed Air Inlet Port 1/4" Female NPT 1/4" Female NPT
Water Requirements Deionized Water (> 5 Meg-Ohm /cm) Deionized Water (> 5 Meg-Ohm /cm)
Max. Ambient Relative Humidity 80 % 80 %
Min/Max Ambient Temperature 60°F/100°F (16°C/40°C) 60°F/100°F (16°C/40°C)
Min/Max Inlet Pressure 40/125 psig (2.7 barg/8.5 barg ) 40/125 psig (2.7 barg/8.5 barg )
Altitude 2000 M 2000 M
Electrical Requirements 100-120/200-240 VAC,47-63Hz 100-120/200-240 VAC,47-63Hz
Power Consumption 480 Watts @ 110 vac, 460 watts @ 220 vac 480 Watts @ 110 vac, 460 watts @ 220 vac
Start Up Time 45 minutes 45 minutes
Fuses 120 vac: 5 x 22 mm, Type T, 250 V, 3.15 Amp 5 x 22 mm, Type T, 250 V, 3.15 Amp
220 vac: 5 x 22 mm, Type T, 250 V, 2.0 Amp 5 x 22 mm, Type T, 250 V, 2.0 Amp
Product Dimensions 13"w x 20"h x 23"d (33cm x 51cm x 58cm) 13"w x 20"h x 23"d (33cm x 51cm x 58cm)
Product Weight/Shipping Weight 53 lbs (24 kg) 53 lbs (24 kg)
Replacement Parts
Description FID 1000 FID 2500 Frequency
Resin Bed Cartridge B02-0323 B02-0323 When Color Changes 3/4
Dessicant Cartridge 1647727 1647727 When Color Changes
Fuses (117 vac, 3.15 Amp) 13216 13216 As needed
Fuses (220 vac, 2 Amp ) 13192 13192 As needed
Maintenance Kit MK7583 MK7583 1 Year
ZAG Catalyst Module B02-0298 B02-0361 2 Years
H2 Cell Assembly B02-0313 7601619 As needed
DIO Water Fill Solenoid B02-0315 B02-0315 As needed
Auto-drain Solenoid 75612 75612 As needed
Recommended Accessories
Accessory P/N
Pressure Regulator (0-130 psig ) 72-130-V883
Installation Kit IK76803
Condenser Assembly 72-100
Flowmeter W-FM7583
HydroGen™ Mate 72-231
* To ensure consistent product
performance and reliability use
only genuine Balston replacement
parts and filter cartridges.
Parker Hannifin UK Ltd
Filter Division Europe
Hermitage Court, Hermitage Lane
Maidstone, Kent ME16 9NT, England
Tel: +44 (0) 1622-723300 Fax: +44 (0) 1622-728703
©Parker Hannifin Corporation 2003, 2006
Printed in U.S.A. Bulletin TI-FID1000C
Parker Hannifin Corporation
Filtration and Separation Division
242 Neck Road, P.O. Box 8223
Haverhill, MA 01835-0723
Tel: 978-858-0505 Fax: 978-858-0625
To Next Page
Loading...
