11GB/IE/NI/CY/MT
13.2 Cleaning the lawnmower via the water con-
nection (15) (Fig. 1, 13, 16)
Note: Push the spark plug connector (12) back
onto the spark plug (12a) properly.
1. First remove the grass collection basket (18).
2. For cleaning, connect a garden hose to the water con-
nection (15) via the built-in plug-in coupling.
3. Turn on the water and start the lawnmower (see 12.2.1).
4. The rotating blade (21) swirls the water.
5. After a few minutes, the lawnmower is free of all adher-
ing dirt and grass residues.
6. Allow the lawnmower to run for a short time without wa-
ter to remove most of the moisture through the circulating
air of the blade (21).
14. Transport
m WARNING!
Danger of injury!
Unintended and unexpected start-up of the product may lead
to injuries.
- Switch the engine off before transporting.
- Allow the engine to cool down.
- Remove the spark plug connector (12) from the spark plug
(12a).
IMPORTANT: For transport, the cutting height must always
be set in the highest position.
1. Empty the fuel tank (8) with a petrol suction pump (not
included in the scope of delivery) (see 16.4.).
2. Drain the engine oil from the warm engine (see 16.3).
3. Clean the cooling fins of the cylinder and the housing
(see 13.1.).
4. Fold in the
upper push bar
(3) (see 15.2.).
5. Wedge a few layers of corrugated cardboard between
the upper push bar (3) and lower push bar (6) and the
engine to prevent any chafing.
15. Storage
m Attention! Do not store the device with the grass col-
lection basket (17) full. In hot weather, the grass begins to
ferment under heat. There is a risk of fire.
Store the device and its accessories in a dark, dry and frost-
free place that is inaccessible to children. The optimum stor-
age temperature lies between 5 and 30 ˚C.
Store the device in its original packaging.
Cover the device to protect it from dust or moisture. Store the
operating manual with the device.
• Clean and maintain the device before storage.
• Never store the lawnmower with petrol in the fuel tank in-
side a building in which fuel vapours may come into contact
with naked flames or sparks.
• Allow the engine to cool down before you put the lawn-
mower in an enclosed area.
• In the event of prolonged storage, empty the fuel tank with
a petrol suction pump (not included in the scope of delivery)
(see 16.4.).
• In order to avoid fire hazards, keep the engine, exhaust
pipe and the area around the fuel tank free of grass, leaves
and leaking grease (oil).
15.1 Preparing the lawnmower for long-term
storage
m WARNING! Do not remove the petrol in enclosed spac-
es, near fire or when smoking. Petrol fumes can cause explo-
sions and fire.
1. Empty the fuel tank (8) with a petrol suction pump (not
included in the scope of delivery) (see 16.4.).
2. Carry out an oil change (see 16.3).
3. Remove the spark plug connector (12) from the spark
plug (12a). Remove the spark plug (12a) with a spark
plug wrench (not included in the scope of delivery).
4. Fill the cylinder with approx. 0.2L of oil from an oil can.
5. Pull the pull starter (20) slowly so that the oil protects the
inside of the cylinder.
6. Screw the spark plug (12a) back in.
7. Clean the cooling fins of the cylinder and the housing
(see 13.1.).
8. Be sure to clean the entire device to protect the paint.
9. Store the device in a well-ventilated area.
15.2 Folding the upper push bar (3) together
m WARNING!
Risk of jamming!
Always hold the upper push bar (3) with one hand at the high-
est point.
- Never place fingers between the upper push bar (3) and
lower push bar (6).
For space-saving storage, the upper push bar (3) is foldable.
1. Remove the grass collection basket (18).
2. Unhook the pull starter (20) from the cable hook (19).
3. Loosen the star grip nuts (4) on the upper push bar (3)
slightly (do not open completely).
4. Move the upper push bar (3) down. The cables must not
be chafed in the process.
16. Maintenance
m WARNING!
Have maintenance and repair tasks that are not
described in this operating manual, carried out
by a specialist workshop. Use only original spare
parts. There is a risk of accident! Always carry
out maintenance and cleaning work with the en-
gine switched off and the spark plug connector
removed. There is a danger of injury!
Let the device cool down before all maintenance
and cleaning tasks. Elements of the engine are
hot. There is a danger of injury and burning!
The product can start unexpectedly and cause injuries.
- Switch off the engine before carrying out any cleaning or
maintenance work.
- Allow the engine to cool down.
- Remove the spark plug connector (12) from the spark plug
(12a).
To Next Page
Loading...
