Peg-Perego switch four - Operating Instructions: Chassis and Seat; Chassis Operation; Seat and Harness Installation; Handlebar, Wheel, and Footrest Adjustments

INSTRUCTIONS
OPENING: Raise the levers on the two handles
together (fig_a) and pull upwards until the
chassis is completely open (fig_b). Check that
the chassis is correctly opened: the side tubes
must be locked together (fig c).
If the front clips do not fasten properly, push
down on the seat until they click into place.
2 FITTING THE BASKET: Slip the loops onto the
hooks at the front (fig a) and the rear (fig. b).
3 FITTING THE CUP HOLDER: insert the cup
holder on the corresponding peg and press
down until it clicks into place (fig a). The cup
holder can be attached to either side of the
chassis.
4 ADJUSTABLE HANDLES: Switch Four: To raise
or lower the handles, hold the button down
(fig. à) and adjust them (fig, b).
5 FIXED OR SWIVELLING FRONT WHEELS: Lift the
levers to prevent the wheels from swiveling
(Па. а) and lower them to allow the wheels to
swivel (fig. b). On uneven surfaces, the wheels
should be set to their fixed position.
6 BRAKES: Press a brake lever to immobilize the
chassis (fig a) and lift the lever to release it
(fig. b).
7 MOUNTING THE SEAT TO THE CHASSIS: the
reversible seat can be attached to the chassis
either facing the person pushing the stroller
(fig. a), or facing forwards (fig, b), place the
seat on the chassis so that it is aligned with
the relative symbols and press downwards
with both hands until you hear two clicks
confirming that it has locked into position.
Ensure the seat is correctly secured by
attempting to pull it upwards by gripping the
front bar.
8 REMOVING THE SEAT FROM THE CHASSIS:
Hold down the two round buttons on the
sides of the seat (fig. a), press the two levers
under the armrests (fig b) and pull up the
seat (fig. c) until it is released. The seat can be
removed from and re-attached to the chassis
when there is a child in it.
9 FRONT BAR: Before attaching the front bar,
press the buttons on the sides of the armrests
and remove the caps (fig. a). To attach the
front bar, guide the connections into the
armrests and push towards the seat until they
click into place (fig. b). To remove the front
bar, press the two buttons and pull it out
(fig. c). To make it easier for the child to get in
and out, it is possible to open the front bar on
one side only. If you wish to use the stroller
without the front bar, put the caps back in
the armrests.
10 BACKREST: to recline the backrest lift
the lever (fig. a) and choose one of the 4
positions (На, b).
11 FOOTREST: to lower the footrest push the two
levers downwards and then push the footrest
=
-13-
downwards (fig. a); to raise the footrest lift it
upwards (fig_b).
12 BABY SAFE: pull the Baby Safe system out
from under the leg rest (fig_a), attach it to the
seat (fig. b), fit the front bar (fig c), unbutton
the fabric covering at the side and then
attach the Baby Safe system to the sides of
the armrests (fig. d). A fitted Baby Safe system
is shown in Figure E.
13 FIVE POINT SAFETY HARNESS: To fasten it,
push the two waist strap buckles (with the
shoulder straps attached - arrow. a) into
the leg divider until they click into place
(arrow. b). To unfasten it, press the round
button in the centre of the buckle (arrow. c)
and pull the waist straps out (arrow. d).
14 To tighten the waist strap, pull on both sides
in the direction of the arrow (arrow. a). To
loosen it do the opposite. The waist strap can
be tightened as far as the safety lock (fig. b).
15 To adjust the height of the safety harnesses,
release the two buckles on the rear of the
backrest.
Pull the shoulder straps towards you
(arrow. a) until the buckles are released and
insert them in the backrest loops (arrow. b).
Remove the shoulder straps from the sack
(arrow. c) and insert them in the most
appropriate loop (arrow. d), then re-attach
the two buckles on the rear of the backrest
(arrow. e) The buckles are securely attached
when a click is heard (fig f).
16 HOOD: to attach the hood insert the
connections into the sides of the seat (only
CA) (fig. a) and then fasten the buttons on
the rear of the backrest (fig. b). To remove
the hood: disengage the connections and
unbutton from the backrest. To raise the
hood: pull it towards you; to close the hood:
push it back. To convert the hood into a
sun canopy, open the double zipper (fig. c)
and unfasten the buttons on the rear of the
backrest. The child's favorite toy can be hung
from the loop on the hood (fig d).
17 FOOT MUFF: Fit the foot muff on and fasten
the buttons under the leg rest (fig a) and on
the sides of it. For the baby carriage version,
raise the leg rest, put the foot muff over
the front bar (fig b) and fasten it with the
buttons on the hood (fig. c).
18 For the stroller version, lower the footrest,
insert the foot muff underneath the front bar
(fig. a) and secure it according to the model
purchased A, B.
19 RAIN CANOPY: position the rain canopy on
the stroller (fig a) and insert the two lateral
loops over the hood buttons (fig b).
20 Secure the rain canopy by attaching the
elastic loop to the rear uprights (fig a) or to
the front uprights (fig b), according to the
seat position.