To Next PageTo Next Page
Need help?Do you have a question about the Pentair Pool Products MiniMax CH 200 and is the answer not in the manual?
General| Brand | Pentair Pool Products |
|---|---|
| Model | MiniMax CH 200 |
| Category | Swimming Pool Heater |
| Language | English |
Manufacturer warranty may be void if heater is improperly installed or operated. Follow manual instructions.
Operating below 68°F causes condensation, damages the heater, and voids the warranty.
Installation must conform to local codes and national/Canadian electrical and fuel gas codes.
Identifies heater model based on input rating (Btu/hr) X 1000.
Identifies heater using a specific format including model, gas type, and options.
Steps to take if you smell gas, including not using electronics and calling the supplier.
Step-by-step instructions for lighting the pilot and main burners.
Steps to safely turn off the gas supply to the heater.
Explains the dual thermostats for pool and spa temperature control.
Describes how to adjust and lock the thermostat knob to prevent exceeding desired temperatures.
Details how to set and adjust the thermostat knob for precise temperature control.
Explains the function of the Pool/Off/Spa selector switch for controlling heating operation.
Recommends checking venting, burner flame, and clearing the heater area every six months or season.
Tips to reduce energy consumption, such as covering the pool and setting appropriate temperatures.
Guidance for operating the heater during spring and fall seasons.
Instructions for winter operation and preventing freezing.
Explains the role of disinfectants in pool and spa water.
Defines disinfectant residual and its importance for killing bacteria.
Explains pH balance and its effects on water chemistry and the heater.
Discusses total alkalinity, its importance for pH control, and testing.
Provides dimensions for outdoor, stackless installation of the heater.
Provides dimensions for outdoor installation with a vent kit.
Provides dimensions for indoor (USA) or outdoor shelter (Canada) installations.
Explains the need for and adjustment of a manual bypass for flow rates exceeding 120 GPM.
Discusses the placement and importance of valves in the circulation piping system.
Discusses adjustments needed for heaters installed below the water level.
Explains when a flow switch is needed and how to install it for specific installation heights.
Describes how to reverse the inlet/outlet water connections without removing the heat exchanger.
Explains factory-installed insulation for high limits when reversing heads.
Details gas line installation, pipe sizing, and leak testing requirements.
Explains gas pipe sizing for propane systems with two-stage regulation.
Procedures for testing and adjusting the regulated manifold pressure.
Specifies inlet and manifold pressure requirements for natural gas and propane.
Requirements for outdoor installation, including clearances and foundation.
Step-by-step guide for installing the outdoor vent cap kit.
Minimum clearances from combustible materials for indoor installations in specific locations.
Information about the stack type indoor draft hood kit.
Step-by-step instructions for installing the indoor draft hood.
Wiring diagram for Millivolt Dual Therm models.
Lists possible causes and remedies for the heater not starting.
Lists possible causes and remedies for short cycling.
Lists possible causes and remedies for knocking noises.
Steps to take if you smell gas, including not using electronics and calling the supplier.
Steps to take if you smell gas, including not using electronics and calling the supplier.
Step-by-step instructions for operating the electronic ignition heater.
Steps to safely turn off the gas supply to the electronic ignition heater.
Steps to take if you smell gas, including not using electronics and shutting off the tank.
Explains the 100% safety lockout feature for propane models.
Step-by-step instructions for operating the propane electronic ignition heater.
Steps to safely turn off the gas supply to the propane electronic ignition heater.
Explains the dual thermostats for pool and spa temperature control in electronic/millivolt models.
Describes how to adjust and lock the thermostat knob for precise temperature settings.
Details how to set and adjust the thermostat knob for desired temperatures.
Explains the function of the Pool/Off/Spa selector switch.
Describes the function of the status indicator lights on the control panel.
Explains the power indicator light and potential causes if it doesn't light.
Explains the thermostat indicator light, which signals a call for heat.
Explains the auxiliary indicator light for remote switch status.
Explains the pressure indicator light and its relation to pump operation.
Explains the heat indicator light, which signals successful burner firing.
Explains the service indicator light, which signals a control problem.
Procedures for testing and adjusting the regulated manifold pressure.
Lists electrical ratings for different voltage options of the IID units.
Provides wiring instructions for transformers for IID electronic units.
Wiring diagram for a 3-wire remote switch setup.
Wiring diagram for a 2-wire remote switch setup.
