Pentair Pool Products Pool and Spa FS-15AZ-SW12 User Manual

16 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

April 2007 G-FSB-SWM

PF 0097/17 03/06

Sandfiltration kit

+ Swimmey pump

INSTALLATION - BETRIEBSANLEITUNG

INSTALLATIE - INSTALACIÓN - INSTALLAZIONE

Table of Contents

Questions and Answers:

T
tonya70Aug 4, 2025
How to fix Pentair Pool Products Water Filtration Systems pump that will not prime?
- Z
  Zachary SaundersAug 4, 2025
  If your Pentair Pool Products Water Filtration Systems pump won't prime, several issues could be the cause. Start by ensuring the strainer pot is full of water and tightened securely. Check the lid O-ring for damage and replace if necessary. Make sure the water level is at an appropriate level. Clean the strainer and skimmer baskets, and open any closed valves in the piping system. Also, inspect the suction line for air leaks and repair them.
R
Rickey BaileyAug 10, 2025
What to do if my Pentair Pool Products Water Filtration Systems motor does not turn?
- D
  dawnfowlerAug 10, 2025
  If the motor of your Pentair Pool Products Water Filtration Systems isn't turning, first ensure the power switch is on and the circuit breaker hasn't tripped; reset it if needed. Verify the pump isn't off due to timer settings. Check that the motor terminal connections are correct. If these steps don't resolve the issue, the motor shaft might be locked by a bad bearing, which would need replacement, or the impeller could be blocked by debris, which should be cleared.
K
Kristen WrightAug 15, 2025
Why is there low flow and high filter pressure in my Pentair Pool Products Pool and Spa FS-15AZ-SW12 Water Filtration Systems?
- C
  Crystal GonzalezAug 15, 2025
  Low flow and high filter pressure in your Pentair Pool Products Water Filtration Systems are often due to a dirty filter. Clean or replace the filter to resolve this. Another potential cause is a restriction in the return line, which should be removed.
A
Andrea MillsAug 22, 2025
What to do if Pentair Pool Products Water Filtration Systems pump is noisy?
- J
  jennifertylerAug 22, 2025
  If your Pentair Pool Products Water Filtration Systems pump is noisy, there are several possible causes. Check for air leaks in the suction and repair them. Another cause may be foreign matter in the pump housing; remove any debris. Cavitation can also cause noise; address the underlying cause of the cavitation.
N
Nancy MooreAug 27, 2025
Why is there low flow and low filter pressure in my Pentair Pool Products Pool and Spa FS-15AZ-SW12?
- K
  Kelly ThompsonAug 27, 2025
  Low flow and low filter pressure in your Pentair Pool Products Water Filtration Systems can occur due to several reasons. Start by cleaning the strainer basket or skimmer basket, as they may be clogged. Another potential cause is a clogged impeller, which should be cleared. Additionally, check for air leaks in the suction line and repair them, or look for any restrictions in the suction line and remove them.

Pentair Pool Products Pool and Spa FS-15AZ-SW12 Specifications

General

Brand	Pentair Pool Products
Model	Pool and Spa FS-15AZ-SW12
Category	Water Filtration Systems
Language	English

Summary

Technical Information

Operation Instructions

Safety Precautions During Operation

Critical warnings for safe valve handling and filter operation under pressure.

Filtration Process Steps

Sequence for setting the valve and starting the pump for normal filtering.

Filter Backwashing Procedure

Steps for cleaning the filter by reversing the water flow and restarting.

General Guidelines

Installation Instructions

Maintenance and Winterizing

Regular Maintenance Tasks

Daily cleaning of the strainer basket and safety warnings before servicing.

Winter Protection Measures

Methods to protect the pump, filter, and piping from freezing temperatures.

Electrical Connection and Wiring

Sand Replacement and Troubleshooting

Sand Replacement Frequency

Instructions for changing the filter sand every five years.

Pump and Motor Troubleshooting

Diagnosing issues like pump not priming, motor not turning, or noisy operation.

Flow and Pressure Troubleshooting

Resolving problems with low flow, high filter pressure, or low filter pressure.

Warranty Information

List of Components

Technical Drawing and Dimensions

Declaration of Conformity

Related product manuals

Onga PA17-BR463

Onga PA24-BR465

Onga PPA15-BR462

Onga PPA17-BR463

Onga PPA20-BR464

Preview: SM/SMBW 2000