Pentair FLECK 5600 SXT - Description and Components Location; By-passing; Programming; Basic Programming

104 pages

To Next Page

To Previous Page

Installer manual Fleck 5600 SXT - Table of Contents

6 / 104 Ref. MKT-IM-013 / E - 23.09.2020

11.9 CE compliance parts list ............................................................................. 102

12 Disposal........................................................................................... 103

Main Page

Table of Contents2
Generalities7
Scope of the Documentation7
Release Management7
Manufacturer Identifier, Product7
Intended Use8
Abbreviations Used8
Norms8
Applicable Norms8
Available Certificates9
Procedure for Technical Support9
Copyright and Trademarks9
Limitation of Liability10
Scan & Service Application11
Safety12
Safety Pictograms Definition12
Serial Label Location13
Hazards13
Personnel13
Material14
Hygiene and Sanitization14
Sanitary Issues14
Hygiene Measures14
Description15
Technical Specifications15
Performance Flow Rate Characteristics16
Outline Drawing17
Components Description and Location18
System Regeneration Cycle20
Downflow Regeneration Cycle (5-Cycles Operation)20
Upflow Regeneration Cycle (5-Cycles Operation)22
Filter Cycle (3-Cycles Operation)24
Configurations for Downflow Softener, Upflow Softener and Filter26
Downflow Softener26
Upflow Softener27
Filter28
Options Available on the Valve29
System Sizing30
Recommended Injector/Dlfc/Blfc-Valve Configuration30
Sizing a Softener (Single Unit)30
Parameters to be Considered30
Determining the Required Volume of Resin31
Resin Exchange Capacity and Capacity of the Unit32
Valve Configuration33
Cycle Time Calculation34
Salt Amount Definition36
Injector Flow Rates36
1650 Injectors37
Installation39
Warnings39
Safety Notices for Installation39
Installation Environement39
General39
Water40
Electrical40
Mechanical41
Integration Constraints41
Valve Connection to Piping42
Top-Mounted Valve Installation42
Block Diagram and Configuration Example44
Regeneration Flows45
Electrical Connections46
Downflow Configuration46
Upflow Configuration47
Bypassing48
Drain Line Connection48
Overflow Line Connection50
Brine Line Connection51
Programming52
Display52
Commands54
Setting the Time of the Day (TD)54
Basic Programming54
Basic Programming Mode Chart54
Day of Override (DO)55
Regeneration Time (RT)55
Feed Water Hardness (H)55
Reserve Capacity (RC) or (SF)55
Current Day of the Week (CD)55
Master Programming Mode55
Master Programming Mode Chart56
Entering Master Programming Mode58
Display Format Mode (DF)58
Regeneration Flow (RF)58
Regeneration Control Type (CT)58
Number of Tanks (NT)59
Tank in Service (TS)59
Unit Capacity (C)59
Filter Capacity (V)59
Feedwater Hardness (H)60
Reserve Selection (RS)60
Days Override (DO)61
Regeneration Time (RT)61
Regeneration Cycle Step Duration61
Day of Week (Dn, N = 1 to 7)62
Current Day (CD)62
Flow Meter Type (FM)62
Meter Pulse (K)63
Filter Programming63
Diagnostic63
Commands63
Current Flow Rate (FR)64
Peak Flow Rate (PF)64
Hours Since Last Regeneration (HR)64
Volume Since Last Regeneration (VU)64
Reserve Capacity (RC)64
Software Version (SV)65
Resetting the Controller65
Soft Reset (SR)65
Hard Reset (HR)65
Commissioning66
Water Filling, Draining and Waterproofness Inspection66
Sanitization67
Disinfection of Water Softeners67
Sodium or Calcium Hypochlorite67
Electro Chlorination68
Operation69
Display69
Display During Operation69
Display During Regeneration69
Recommendations70
Manual Regeneration70
Manual Delayed Regeneration70
Immediate Regeneration70
To Advance Regeneration Cycles70
Operation During a Power Failure71
Maintenance72
General System Inspection72
Water Quality72
Mechanical Checks72
Regeneration Test73
Recommended Maintenance Plan74
Valve Used for Softening74
Valve Used for Filtration76
Recommendations77
Use Original Spare Parts77
Use Original Approved Lubricants77
Maintenance Instructions77
Cleaning and Maintenance77
First Steps77
Controller Motor Replacement78
Controller Replacement79
Piston And/Or Brine Valve And/Or Seal and Spacer Kit Replacement80
Microswitches And/Or Drive Cam Replacement82
Brine Cam Replacement83
Injector Cleaning84
BLFC Cleaning85
Valve on Tank Assembly86
Troubleshooting87
Error Detection90
Motor Stall/Cam Sense Error90
Motor Run-ON Error/Cycle Sense Error91
Regeneration Failure91
Memory Error92
Spare Parts and Options93
Valve Parts List93
Power Head Parts List95
Safety Brine Valves List96
Safety Brine Valves 2310 Parts List97
Bypass Valve Assembly List97
1" BSP Female Stainless Steel Bypass97
1" BSP Female Brass Bypass with Mixing98
Plastic Bypass (no Yoke)99
Distribution Systems Parts List100
Air Checks List101
Meters Parts List101

Pentair FLECK 5600 SXT - Description and Components Location; By-passing; Programming; Basic Programming

Table of Contents

Other manuals for Pentair FLECK 5600 SXT

Related product manuals