(.
8.
Adjustment
and
Confirmation
8-
1.
FUNCTION
CHECK
CD
Preparation
1.
Apply
the power to the
body.
2.
Attach the
FA
lens
to
the
body.
@ Drive mode
SW
(Main
SW)
and
Release
SW
1.
Set the Drive mode
SW
from
•t• to • 0 •. (
__.
Main
SW/ON)
Then confirm the
LCD
display
showing exposure mode
"P",
"Av",
"Tv"
or
"M".
2.
Depress the release button
halfway.
(
__.
Metering
SW/ON)
And
make sure that the metering stays
on
for approx.
10
sec.
and
the finder
LCD
is
displayed.
3.
Turning the Drive
mode
SW
to " 0
•,
• Oi "
and
" 0
•,
check the function
at
the each
mode.
@ Auto/Manual switching
Set the shutter speed
dial
to
"A".
And
set
the
diaphragm
ring
to
"A",
then
confirm
the
LCD
showing exposure mode
"P".
Change the diaphragm ring to
manual
stop, then
confirm
the
LCD
showing exposure
mode
"Av".
@ Shutter speed
dial
Turning the shutter speed
dial,
make
sure that the finder
LCD
will
be displayed the same shutter speed
as
setting the shutter speed
dial.
@ Exposure compensation
dial
Set the exposure
mode
"P',
"Av"
or 'Tv".
Turning the exposure compensation
dial
from
"+3" to
"-3"
except
•o
•, make sure that the finder
LCD
will
be displayed
~
- mark and the compensation value in bar graph
at
the each stop of the
dial.
@ Film speed setting
(manual)
Set the exposure compensati
on
dial
to
"I
SO".
By
depressing the Spot
AF
button, the film speed
will
be increased.
By
depressing the Spot
AF
button while h
olding
down
the
dial
lock button, the
film
speed
will
be
decreased.
CT)
AF
function
Set the Focus mode
SW
to
"AF".
1.
While aiming the
AF
frame
at
a subject
and
deiressing the shutter button
halfway,
AF
function
will
operate to in-focus, and then the
focus
indication
in
the viewfinder
will
light up with sounding
an
electronic beep.
2.
Cover the front of lens with a
hand.
By
depressing the shutter button
halfway,
AF
function
will
operate to rotate the lens between •
oo
•
and
short distance end.
Then the focus indication
will
blink
and
the shutt
er
will
not be able to release.
@ Back cover
SW,
Film winding/rewinding
1.
Load a test
film,
close the back cover
and
turn
Main
SW
on, then the film
will
advance
to
the first
frame.
At the same time, the
film
counter
wilt
change
"O"
to
•1•.
Release shutter several times
and
confirm
film advance
and
counter change.
2. Depress the rewind button,
make
sure that the rewinding of
film
will start.
Confirm winding and rewinding
will
not make
any
strange noise.
® Flash check
1.
Set the flash
to
the pop- up condition, then confirm the flash ready mark (
~
) comes
up.
2.
By
depressing the Multi-function button, the flash function
will
change accordingly as shown below.
"<>·--.· ·
•--.•
• <>·--.·
3.
Set the exposw-e mode "P', check the Automatic
flash
function ( • ) as
follows
.
· When the subject
is
dark
and
release the shutter, the
flash
will fire.
• When the subject
is
btight and release the shutter, the
flash
will not fire.
(Continued)
27250
1~/?A
To Next Page
Loading...
