PhiBer BigBale Accumulator AC3108 Series

Questions and Answers

J
Jennifer DukeAug 13, 2025
Why is my PhiBer BigBale Accumulator AC3108 Farm Equipment tractor hydraulic oil overheating?
- W
  Walter CrawfordAug 13, 2025
  To prevent tractor hydraulic oil from overheating in your PhiBer Farm Equipment, reduce the tractor hydraulic oil flow setting. Ensure that low-pressure return flow discharges directly into the tractor hydraulic reservoir. For older tractors, you may need to plumb the return flow to a port for direct discharge into the reservoir. Also, remove and inspect the check valve, cleaning any debris before replacing it, and inspect quick coupler tips for proper action and blockages.
M
Michele WalkerAug 17, 2025
What to do if side shift and push off trucks on PhiBer BigBale Accumulator AC3108 don't move?
- J
  Julian HarrisAug 17, 2025
  If the side shift and push off trucks on your PhiBer Farm Equipment aren't moving when you actuate the tractor hydraulic lever, check the following: ensure the hydraulic hose connections are correct at the tractor hydraulic quick couplers; inspect and clean the wiring harness coupling; replace the 7 A fuse on the monitor in the tractor cab; check and adjust the limit switch settings for side shift and push off modes; and reset the electronic monitor by toggling the power switch to “OFF”, then pressing and holding the “EJECT” button for 3 seconds until the indicator lights strobe.
D
dsmithAug 20, 2025
What to do if push off truck moves slightly after resetting PhiBer BigBale Accumulator AC3108 Farm Equipment accumulator?
- E
  Edward BenjaminAug 21, 2025
  If the push off truck on your PhiBer Farm Equipment moves slightly after resetting the accumulator, even when other tractor hydraulics appear to function correctly, there may be a hydraulic lock. Place the tractor hydraulic control lever in the float position or disconnect the return hydraulic hose coupler to drain off excessive oil. Push the center pins of the main valve until all pins move freely, then re-connect the hydraulic hose coupler. Ensure that return oil discharges into the tractor hydraulic reservoir, and reduce the tractor hydraulic flow to the accumulator to 12 gal-US/min (45.4 L/min) or less.
H
Heidi MercadoAug 25, 2025
How to fix inactive electronic system on PhiBer Farm Equipment?
- J
  Joseph GarciaAug 25, 2025
  If the electronic system on your PhiBer Farm Equipment appears inactive and the indicator lights do not strobe at start-up, toggle the power switch to “OFF”. Open the control box under the deck of the accumulator, remove and replace the 800 mA fuse. Then, toggle the power switch back to “ON.”
P
Phillip BrownAug 28, 2025
What to do if bale trigger does not activate side shift truck on PhiBer BigBale Accumulator AC3108?
- D
  Dustin AndersonAug 29, 2025
  If the bale trigger does not activate the side shift truck on your PhiBer Farm Equipment, measure the gap between the proximity switch and the trigger plate. If necessary, adjust the gap to be between 3/16 - 1/8” (1.5 - 3 mm).
M
Mark BenjaminSep 1, 2025
Why does the side shift operate prematurely on my PhiBer BigBale Accumulator AC3108 Farm Equipment?
- V
  Vanessa MoralesSep 1, 2025
  The side shift on your PhiBer Farm Equipment might be operating prematurely because the bale trigger bounces on rough terrain or bales sag as they leave the chamber on the baler. To resolve this, tighten the spring on the bale trigger, adjust the bale trigger downward to make it less sensitive, adjust the bale trigger forward for haylage bales, and raise the front of the accumulator.
R
Robert VasquezSep 5, 2025
How to reset accumulator on PhiBer BigBale Accumulator AC3108?
- A
  Alexander JonesSep 5, 2025
  If the accumulator on your PhiBer Farm Equipment does not work, check the Emergency Stop Switch. If it's pushed in, turn it clockwise to reset.
M
Melissa TaylorSep 9, 2025
What to do if Machine Function Halted on PhiBer BigBale Accumulator AC3108 Farm Equipment?
- C
  Chris TaylorSep 9, 2025
  To address a halted machine function on your PhiBer Farm Equipment, enable the remote on the tractor and check all sensors on the diagnostics page. This issue may be due to hydraulic flow not being turned on or a hydraulic time out due to sensor failure.

Summary

Introduction

Description of the Machine

Bale Packaging Modes

Explains the different configurations for arranging bales.

Illustration of the Machine

Large Square Bale Accumulator Assembly

Details the components of the accumulator assembly with visual aids.

Virtual Terminal

Describes the use of the ISOBUS terminal for machine interaction.

Serial Number Location

Identifies the location of the serial number plate for service.

Safety

Safety Alert Symbols Explained

Explains the purpose and meaning of safety alert symbols used in the manual and on the machine.

Understanding Signal Words (DANGER, WARNING, CAUTION)

Defines the meaning of DANGER, WARNING, and CAUTION signal words for hazard identification.

Operator Safety Responsibility

Outlines the operator's duties for safe operation, adjustment, and maintenance.

General Safety Practices and Guidelines

Provides essential safety guidelines for operating the bale accumulator safely.

Maintenance Safety Precautions

Specific safety precautions to be followed during maintenance procedures.

Hydraulic System Safety

Safety guidelines related to the hydraulic system of the accumulator.

Installation Safety Procedures

Safety measures required during the installation process of the accumulator.

Safe Transporting Guidelines

Safety guidelines and warnings for transporting the bale accumulator.

Safe Storage Practices

Safety instructions and recommendations for storing the bale accumulator.

Safety Signs and Explanations

Information on safety signs, their location, and their specific meanings.

Emergency Stop Button Functionality

Information on the location, function, and operation of the emergency stop button.

Specifications

Bale Accumulator Specifications

Technical details and dimensions of the bale accumulator models.

Tractor Requirements

Specifies the necessary tractor features for operating the accumulator.

Hardware Torque

Torque Specifications

Provides torque values for various bolts and fittings.

Operation

Hydraulic System Set-up

Instructions for correctly setting up the tractor hydraulics for optimal accumulator performance.

Bale Ejection Cycle Mode Selection

How to select and configure different bale ejection modes for the accumulator.

Safe Start-up Procedure

Step-by-step instructions to follow for a safe and proper start-up of the accumulator.

Field Operation Guidelines

General guidelines and best practices for operating the accumulator in the field.

Automatic Bale Ejection System

Details on how the automatic bale ejection system functions and operates.

Manual Bale Ejection Procedure

Instructions for manually ejecting bales from the accumulator.

Hold Mode Operation

Explanation of the hold mode feature and its application in bale accumulation.

ISOBUS Software and Configuration

Information on using the ISOBUS software for updates and advanced configuration.

Icon Guide

Standard and Accumulator Icons Explained

Explains the meaning of various icons used on the operator interface.

Start-up Interface Navigation

Describes the initial screens and selections during start-up.

PhiBer Accumulator App

Planning Mode and Zone Creation

Guide to using the app for planning bale ejection locations and creating zones.

How the Zones Work in the App

Explains the functionality of zones within the planning app for bale ejection.

Bale Eject Mode Setup via App

How to set up automatic bale ejection using the mobile application.

Bluetooth and Wifi Connection

Instructions for connecting the device to the accumulator wirelessly.

Remote Control Functionality

Describes the remote control functionality via the mobile app.

Manual Eject via App

How to perform a manual eject using the mobile application.

Software Updates via App

Procedures for updating the accumulator software through the app.

Downloading and Sending Log Files

Guide to accessing and sharing diagnostic log files for support.

Bale Trigger Adjustment

Bale Trigger Vertical Adjustment

Steps to adjust the vertical position of the bale trigger for proper sensing.

Bale Trigger Horizontal Adjustment

Steps to adjust the horizontal position of the bale trigger for proper sensing.

Transporting

Safe Transporting Guidelines

Safety warnings and procedures for transporting the bale accumulator on public roads.

Storage

Storage Safety and Seasonal Procedures

Instructions for safe storage and preparation of the accumulator for the next season.

Recommended Settings

Flow Settings and Cycle Times

Chart showing recommended hydraulic flow settings and corresponding cycle times.

Hitch Height Adjustment

Guidelines for setting the optimal hitch height for stability and bale retention.

Maintenance

Limit Switch Maintenance and Checks

Daily checks for limit switches to ensure proper function and clear obstructions.

Wheel Lug Nut Tightness Checks

Procedures for checking and maintaining the tightness of wheel lug nuts.

Roller Bearing Lubrication

Lubrication schedule and instructions for the accumulator's roller bearings.

Hitch Pivot Lubrication and Maintenance

Lubrication guidelines and maintenance for the hitch pivot assembly.

Bale Trigger Spring Tension Adjustment

Procedure for checking and adjusting bale trigger spring tension for correct activation.

Wheel Bearing Maintenance and Repacking

Instructions for cleaning, inspecting, and repacking wheel bearings.

Hydraulic Cylinder Replacement

Air Removal Procedure After Replacement

Steps for removing air from the hydraulic system after cylinder replacement.

Hydraulic Schematic

Solenoid Control Valve and Ports Overview

Identifies key components and ports in the hydraulic schematic diagram.

Electrical Schematic

Controller and Wiring Diagram

Details the electrical components and wiring connections for the machine.

Lights

Lighting System Wiring Diagram

Illustrates the wiring connections for the machine's lighting system.

Troubleshooting

Troubleshooting: Accumulator Not Working

Addresses common issues and solutions when the accumulator fails to operate.

Troubleshooting: Side Shift and Push Off Movement

Solutions for problems related to the movement of side shift and push off trucks.

Troubleshooting: Hydraulic Oil Overheating

Explains causes and provides solutions for hydraulic oil overheating issues.

Troubleshooting: Machine Function Halted

Provides solutions for scenarios where the machine's primary function is halted.

Installation

Hitch Kit Mounting Guidelines

General guidance and considerations for mounting the bale accumulator hitch kit.

Preparing Tractor and Baler for Installation

Step-by-step instructions to prepare the tractor and baler for accumulator installation.

Accumulator Placement and Alignment

Instructions on correctly positioning and aligning the accumulator behind the baler.

Optimum Hitch Height Adjustment

Guidelines for setting the optimal hitch height for stability and proper operation.