70
QUICK REFERENCE KEYBOARD COMMAND TABLE
System Commands
Log-on ON n ENTER n ENTER NOTE 1
Log-off USER OFF NOTE 1
Program Keyboard Memory MEMORY n ENTER [ ] ENTER NOTE 3
Run Keyboard Memory MEMORY n RUN NOTE 3
Switcher Commands
Select Camera n ENTER
Select Monitor MONITOR n ENTER
Program Sequence PROGRAM n ENTER [ ] ENTER NOTE 2
Request Sequence SEQUENCE n ENTER NOTE 2
Run/Hold RUN/HOLD
Direction PREVIOUS/NEXT
Lock/Unlock Monitor MONITOR n LOCK ON/OFF NOTE 2
Remote Camera Control Commands
Lock/Unlock Camera n LOCK ON/OFF NOTE 2
Move Camera {JOYSTICK}
Lens Control {ROCKER SWITCHES}
Record Position SET n ENTER
Recall Position SHOT n ENTER
Auxiliary On/Off ON/OFF n ENTER
Dither Control ON/OFF 5 ENTER
Alarm Control Commands
Arm/Disarm Camera ALARM n ON/OFF
Arm/Disarm All Cameras USER ALARM ON/OFF
Arm/Disarm Monitor USER MONITOR ON/OFF
Acknowledge ACKNOWLEDGE NOTE 2
User Function Commands
Local Keyboard Test USER 1 ENTER [ ] ENTER
Show Keyboard Port Number USER 2 ENTER USER
Select Keyboard Beeper On/OFF USER 3 ENTER ON/OFF USER
Adjust Position of Monitor Overlay USER 4 ENTER {JOYSTICK} ENTER USER NOTE 2
Monitor Display Brightness/Status USER 5 ENTER {JOYSTICK} ENTER USER NOTE 2
Select Monitor Display Option USER 6 ENTER {JOYSTICK} ENTER USER NOTE 2
Set Time USER 7 ENTER {JOYSTICK} ENTER USER NOTE 2
Set Date USER 8 ENTER {JOYSTICK} ENTER USER NOTE 2
Set Camera ID USER 9 ENTER {JOYSTICK} ENTER USER NOTE 2
Change User Password USER 10 ENTER n ENTER n ENTER n ENTER USER
Select Time/Date Format USER 11 ENTER {JOYSTICK} ENTER USER NOTE 2
Default All Monitor Overlays USER 12 ENTER {JOYSTICK} ENTER USER NOTE 2
Print System Configuration Tables USER 13 ENTER {JOYSTICK} ENTER USER NOTE 2
Reset System USER 15 ENTER n ENTER NOTE 2
Time Event Enable/Disable USER 16 ENTER {JOYSTICK} ENTER USER NOTE 2
Set Monitor ID USER 17 ENTER {JOYSTICK} ENTER USER NOTE 2
Print Sequence USER 18 ENTER {JOYSTICK} ENTER USER NOTE 2
Select Alarm Response USER 19 ENTER {JOYSTICK} n ENTER USER NOTE 2
Select Printer Verbosity USER 20 ENTER {JOYSTICK} ENTER USER NOTE 2
Designate Alarm Monitor Type USER 21 ENTER {JOYSTICK} n ENTER USER NOTE 2
Select Control Code Format USER 22 ENTER {JOYSTICK} ENTER USER
Display CPU Software Version Number USER 23 ENTER
Set Positions On All Monitor Displays USER 24 ENTER {JOYSTICK} ENTER USER
Set Brightness on All Monitor Displays USER 25 ENTER {JOYSTICK} ENTER USER
Set Display Options On All Monitors USER 26 ENTER {JOYSTICK} ENTER USER
Select Keyboard Log-in USER 27 ENTER {JOYSTICK} ENTER USER NOTE 2
Select Console Log-in USER 28 ENTER {JOYSTICK} ENTER USER NOTE 2
Reset RS-232 Parameters to Default USER 29 ENTER {JOYSTICK} ENTER USER NOTE 2
Select Console Port RS-232 Parameters USER 30 ENTER {JOYSTICK} ENTER USER NOTE 2
Select Printer Port RS-232 Parameters USER 31 ENTER {JOYSTICK} ENTER USER NOTE 2
Select Alarm Port RS-232 Parameters USER 32 ENTER {JOYSTICK} ENTER USER NOTE 2
Display User Number and Priority USER 33 ENTER
NOTE 1. This function is active only if selected by the system installer.
NOTE 2. Access to this function is based on USER priority level. Refer to the appropriate section of the operating instructions for more information.
NOTE 3. This function is not applicable to TC8554 and TC8555 keyboards.
To Next Page
Loading...
