Philips AZ1018 - Controls; Top and Front Panels; Back Panel; Power Supply

INSTRUCTIONS FOR USE
3-4
PCS 107 141
Programming track numbers You may store up to 20 tracks in the desired sequence. If you like, store any track more than once.
1 In the STOP mode, press SEARCH ∞ or
§ for your desired track.
2 When your chosen track number appears,
press CD MODE/ PROGRAM once to store the track. ‹ The display shows PROGRAM and
'P
ro
g' briefly followed by your selected
track number.
‹ If you attempt to programme without
first selecting a track number, no SEL is shown.
3 Repeat steps 1 to 2 to select and store all
desired tracks in this way. ‹ FULL is displayed if you attempt to
programme more than 20 tracks.
4 To play your programme, press
PLAY•PAUSE 2;.
Reviewing your programme
• In the STOP mode, press and hold down
CD MODE/ PROGRAM for more than one second. ‹ The display shows all your stored track
numbers in sequence.
Erasing a programme You can erase the contents of the memory by: – opening the CD door; – selecting RADIO or TAPE source; – pressing STOP 9 (twice during playback or in the stop position.) ‹ Display: shows '
no
P
ro
g' briefly when
the programme is cancelled.
CD-Player
D
I
G
I
T
A
L
T
U
N
E
R
B
A
S
S
R
E
F
L
E
X
S
P
E
A
K
E
R
S
Y
S
T
E
M
TAP
OFF
MW
FM
CD
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
R
E
C
O
R
D
POWER
VOLUME
CD MODE
PROGRAM
PRESET
SEARCH
PLA
Y
-
PAUSE
STOP
FM•MW
C
D
R
A
D
I
O
C
A
S
N
E
P
O
O
T
T
F
I
L
BATT
LOW
CASSETTE RECORDER Cassette playback
1 Adjust the POWER slider to TAPE/OFF. 2 Press STOP•OPEN 9/ to open the
cassette door and insert a recorded cassette.
3 Close the cassette door. 4 Press PLAY 1 to start playback.
‹ Display: shows tAPE throughout tape
operation.
5 To pause playback press PAUSE ;.To
resume, press the key again.
6 By pressing 5 or 6, fast winding of the
tape is possible in both directions.To stop fast winding, press STOP•OPEN 9/.
7 To stop the tape, press STOP•OPEN 9/. • The keys are automatically released at the
end of the tape, the tAPE indication goes out and the set is switched off, except if PAUSE ; has been activated.
General information on recording
• Recording is permissible insofar as copyright
or other rights of third parties are not infringed.
• This deck is not suited for recording on
CHROME (IEC II) or METAL (IEC IV) type cassettes. For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not been broken.
• The best recording level is set automatically.
Altering the VOLUME and DBB controls will not affect the recording in progress.
• At the very beginning and end of the tape,
no recording will take place during the 7 seconds when the leader tape passes the recorder heads.
• To protect a tape from accidental erasure,
have the tape in front of you and break out the left tab. Recording on this side is no longer possible.To record over this side again, cover the tabs with a piece of adhesive tape.
Cassette Recorder Recording
∑
D
I
G
I
T
A
L
T
U
N
E
R
B
A
S
S
R
E
F
L
E
X
S
P
E
A
K
E
R
S
Y
S
T
E
M
TAP
OFF
MW
FM
CD
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
R
E
C
O
R
D
POWER
VOLUME
CD MODE
PROGRAM
PRESET
SEARCH
PLA
Y
-
PAUSE
STOP
FM•MW
A
Z
1
0
1
8
C
D
R
A
D
I
O
C
A
S
S
E
T
T
E
R
E
C
O
R
D
E
R
N
E
P
O
O
T
T
F
I
L
BATT
LOW