EasyManuals Logo

Philips BT6000 Quick Start Guide

Philips BT6000
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
A B
NFC
Philips BT6000
¿Alguna
pregunta?
Contacte con
Philips
ES Guía de inicio rápido
EN Quick Start Guide
Specications are subject to change without notice.
2016 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under
the responsibility of Gibson Innovations Ltd., and Gibson
Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used under
license from Koninklijke Philips N.V.
BT6000_77_QSG_V1.0
Siempre a su disposición para ayudarle
Para registrar su producto y obtener información de contacto y
asistencia, visite
www.philips.com/support
BT6000
Short User Manual
www.philips.com/welcome
Always there to help you
Register your product and get support at
Question?
Contact
Philips
ES
Indicador LED Estado de la batería
Rojo permanente Cargando
Desactivado Totalmente cargada
Nota:
El indicador LED rojo parpadea cuando la batería se está
agotando.
EN
LED indicator Battery status
Solid red Under charging
Off Fully charged
Note:
The red LED indicator ashes when the battery level is
low.
OFF
ON
ES
Para encender el altavoz o apagarlo, gire el control en el sentido de las agujas del reloj o en sentido
contrario al de las agujas del reloj hasta que oiga un clic.
Nota:
El altavoz cambia al modo de espera después de 15 minutos de inactividad.
Si el indicador LED se ilumina de forma permanente en rojo y el altavoz no responde al
pulsar los botones, signica que el altavoz está en modo de demostración. Mantenga pulsado
PAIRING durante 15 segundos para salir de este modo.
EN
To turn the speaker on or off, rotate the knob clockwise or anticlockwise until you hear a click.
Note:
The speaker switches to standby mode after 15 minutes of inactivity.
If the LED indicator is solid red, and the speaker has no response when pressing any key, it
means the speaker is in DEMO mode. Press and hold PAIRING for 15 seconds to exit this
mode.
3 sec.
3 sec.
ES
Cuando hay una llamada entrante:
Acción Función
Responde a una llamada entrante.
Durante una llamada, naliza la llamada actual.
3 sec.
Rechazar una llamada entrante.
Durante una llamada, transere la llamada a su
dispositivo móvil.
Nota: La reproducción de música se pone en pausa cuando hay
una llamada entrante.
ES
Reproducción desde dispositivos con Bluetooth
1 Encienda el altavoz.
» El indicador LED azul parpadea.
2 Opción A: para un dispositivo Bluetooth compatible con NFC: 1) Active la función NFC en el dispositivo. 2) Toque la etiqueta NFC
en la parte superior del altavoz con la parte NFC del dispositivo Bluetooth. 3) Siga las instrucciones en pantalla para completar el
emparejamiento y la conexión.
Opción B: Para otros dispositivos Bluetooth: 1) En el dispositivo Bluetooth, active la función Bluetooth y busque los dispositivos Bluetooth.
2) Seleccione [Philips BT6000] en el dispositivo que va a emparejar. Si es necesario, introduzca la contraseña predeterminada “0000”.
» Una vez realizada correctamente la conexión, el altavoz emite dos pitidos y el indicador LED se ilumina en azul de forma permanente.
Si no encuentra [Philips BT6000] en el dispositivo para realizar el emparejamiento, mantenga pulsado PAIRING hasta que oiga un
pitido e inténtelo de nuevo.
3 Reproduzca el audio en el dispositivo Bluetooth.
» El audio se transmite desde el dispositivo al altavoz.
Consejo: Antes de conectar otro dispositivo Bluetooth, desconecte el dispositivo actual.
ES
Cuando no hay ninguna llamada entrante:
Acción Función
3 sec.
Acceda al modo de emparejamiento mediante
Bluetooth.
Desconecte la conexión Bluetooth actual.
ES
No contiene fuente de alimentación para su uso.
EN
The adaptor is not supplied.
EN
Play from Bluetooth-enabled devices
1 Turn on the speaker.
» The blue LED indicator ashes.
2 Option A: For a Bluetooth device that supports NFC: 1) Enable NFC feature on your device. 2) Tap the NFC tag on the top
of the speaker with the NFC area of your Bluetooth device. 3) Follow the on-screen instructions to complete the pairing and
connection.
Option B: For other Bluetooth devices: 1) On your Bluetooth device, enable Bluetooth and search for Bluetooth devices. 2)
Select [Philips BT6000] displayed on your device for pairing. If necessary, enter default password “0000”.
» After successful connection, the speaker beeps twice, and the LED indicator turns solid blue.
If you fail to nd [Philips BT6000] on your device for pairing, press and hold PAIRING until you hear beep sound, and
then try again.
3 Play audio on the Bluetooth device.
» Audio streams from your device to the speaker.
Tip: Before connecting another Bluetooth device, disconnect the current device rst.
EN
When there is an incoming call:
Action Function
Answer an incoming call.
During a call, end the current call.
3 sec.
Reject an incoming call.
During a call, transfer the call to your mobile
device.
Note: Music play pauses when there is an incoming call.
EN
When there is no incoming call:
Action Function
3 sec.
Enter Bluetooth pairing mode.
Disconnect current Bluetooth connection.

Other manuals for Philips BT6000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Philips BT6000 and is the answer not in the manual?

Philips BT6000 Specifications

General IconGeneral
Product typeStereo portable speaker
On/off switchYes
Product colorBlack
Protection featuresWater resistant
International Protection (IP) codeIPX4
Number of drivers2
Number of speakers1
Audio output channels2.0 channels
Subwoofer driver diameter38.1 mm
Frequency range100 - 20000 Hz
RMS rated power12 W
Bluetooth version4.0
Bluetooth profilesA2DP, AVRCP, HFP
Connectivity technologyWireless
Package depth105 mm
Package width282 mm
Package height108 mm
Package weight790 g
Battery typeBuilt-in
Battery voltage3.7 V
Battery capacity4400 mAh
Power source typeBattery
Battery life (max)8 h
AC adapter frequency50/60 Hz
AC adapter input voltage100 - 240 V
Power consumption (standby)1 W
Recommended usageUniversal
Weight and Dimensions IconWeight and Dimensions
Depth71 mm
Width188 mm
Height70 mm
Weight490 g

Related product manuals