Listening to an external source
You can listen to the sound of the connected
external device through your system’s speakers.
1
Use the red/ white audio cables to connect the
system’s AUX/CDR IN (R/L) terminals to the
AUDIO OUT terminals on the other
audio/ visual device (such as a TV, VCR, Laser Disc
player, DVD player or CD recorder)
If the connecting device has only a a single
audio out terminal, connect it to the AUX /CDR
IN left terminal. Alternatively, you can use a
“single to double” cinch cable, but the output
sounds still remain mono.
2
Press AUX repeatedly.
Select “AUX” when connecting to a TV, VCR
or Laser Disc player.
Select “AUX/CDR” when connecting to a CD
recorder or DVD player.
3
Press PLAY on the connected device to start
playback.
Notes:
–All the sound control features (DSC, VEC for
example) are available for selection.
–Always refer to the owner’s manual of the other
equipment for complete connection and use
details.
Timer Operations Other Connection
Temporarily deactivating the wake up
timer
You are only able to activate the Snooze
function within 30 minutes after the timer wakes
up from standby mode.
1
After timer wake up, press SNOOZE on the
remote.
The system will switch to standby mode for
five minutes. After that, it resumes the last
selected source again.
2
To cancel the snooze function, press SNOOZE
again.
Sleep timer setting
The sleep timer turns the system to Eco Power
standby mode at a preselected time.
1
Press SLEEP repeatedly until it reaches the
desired preset turn-off time.
The selections are as follows (time in
minutes):
15 ™ 30 ™ 45 ™ 60 ™ 90 ™ 120 ™
OFF ™ 15 …
SLEEP
is shown, except for "OFF" mode.
To view or change the setting, repeat the
above.
2
Before the system switches to Eco Power
standby mode, a countdown of 10 seconds is
displayed.
"SLEEP 10" ™ "SLEEP 9".... ™ "SLEEP 1"
™ "SLEEP"
To cancel th
e sleep timer
Press SLEEP repeatedly until "OFF" is displayed,
or press the STANDBY ON B button.
Important notes for users in the
U.K.
Mains plug
This apparatus is fitted with an approved 13
Amp plug. To change a fuse in this type of plug
proceed as follows:
1
Remove fuse cover and fuse.
2
Fix new fuse which should be a BS1362 5 Amp,
A.S.T.A. or BSI approved type.
3
Refit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 5 Amp. If a plug without a fuse
is used, the fuse at the distribution board
should not be greater than 5 Amp.
Note: The severed plug must be disposed of
to avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with
the following code: blue = neutral (N),
brown = live (L).
¶ As these colours may not correspond with the
colour markings identifying the terminals in
your plug, proceed as follows:
– Connect the blue wire to the terminal
marked N or coloured black.
– Connect the brown wire to the terminal
marked L or coloured red.
–Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath
of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may
require consent. See Copyright Act 1956 and
The Performer’s Protection Acts 1958 to 1972.
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er
derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
CAUTION
Use of controls or adjustment or
performance of procedures other than
herein may result in hazardous
radiation exposure or other unsafe
operation.
VAROITUS
Muiden kuin tässä esitettyjen
toimintojen säädön tai asetusten
muutto saattaa altistaa vaaralliselle
säteilylle tai muille vaarallisille
toiminnoille.
Italia
DICHIARAZIONE DI CONFORMITA ’
Si dichiara che l’apparecchio MC M530, Philips
risponde alle prescrizioni dell’art. 2 comma 1 del
D.M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer Electronics
Philips, Glaslaan 2
5616 JB Eindhoven, The Netherlands
To Next Page
Loading...
