Philips Pocket Memo DPM8500 - Set Lengths for Code

35Barcode scanner configuration guide
Set Lengths for Code 93
Parameter # L1 = 1Ah L2 = 1Bh
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for Code
93 may be set for any length, one or two discrete lengths, or lengths within a specific range.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select Code 93 One Discrete Length,
then scan 1, 4, to limit the decoding to only Code 93 symbols containing 14 characters. Numeric bar codes begin on page 56. To change the
selection or cancel an incorrect entry, scan Cancel on page 57.
Parameter Menus 4 - 41
Code 93
Enable/Disable Code 93
Parameter # 09h
To enable or disable Code 93, scan the appropriate bar code below.
Enable Code 93
(01h)
*Disable Code 93
(00h)
Set Lengths for Code 93
Parameter # L1 = 1Ah L2 = 1Bh
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for Code 93 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
Code 93 One Discrete Length, then scan 1, 4, to limit the decoding to only Code 93 symbols containing 14 characters.
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Code 93 - One Discrete Length
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select Code 93 Two Discrete
Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing 2 or 14 characters. Numeric bar codes begin on page 56. To
change the selection or cancel an incorrect entry, scan Cancel on page 57.
4 - 42 SE655 Decoded Linear Imaging Engine
Set Lengths for Code 93 (continued)
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select Code 93 Two Discrete Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing
2 or 14 characters. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan
Cancel on page 4-74.
Code 93 - Two Discrete Lengths
Length Within Range - This option sets the unit to decode a code type within a specified range. For example, to
decode Code 93 symbols containing between 4 and 12 characters, first scan Code 93 Length Within Range, then scan
0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To
change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Code 93 - Length Within Range
Any Length - Scan this option to decode Code 93 symbols containing any number of characters.
Code 93 - Any Length
Length Within Range - This option sets the unit to decode a code type within a specified range. For example, to decode Code 93 symbols containing
between 4 and 12 characters, first scan Code 93 Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a
leading zero). Numeric bar codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57:
4 - 42 SE655 Decoded Linear Imaging Engine
Set Lengths for Code 93 (continued)
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select Code 93 Two Discrete Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing
2 or 14 characters. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan
Cancel on page 4-74.
Code 93 - Two Discrete Lengths
Length Within Range - This option sets the unit to decode a code type within a specified range. For example, to
decode Code 93 symbols containing between 4 and 12 characters, first scan Code 93 Length Within Range, then scan
0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To
change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Code 93 - Length Within Range
Any Length - Scan this option to decode Code 93 symbols containing any number of characters.
Code 93 - Any Length
Any Length - Scan this option to decode Code 93 symbols containing any number of characters.
4 - 42 SE655 Decoded Linear Imaging Engine
Set Lengths for Code 93 (continued)
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select Code 93 Two Discrete Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing
2 or 14 characters. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan
Cancel on page 4-74.
Code 93 - Two Discrete Lengths
Length Within Range - This option sets the unit to decode a code type within a specified range. For example, to
decode Code 93 symbols containing between 4 and 12 characters, first scan Code 93 Length Within Range, then scan
0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To
change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Code 93 - Length Within Range
Any Length - Scan this option to decode Code 93 symbols containing any number of characters.
Code 93 - Any Length