39Barcode scanner configuration guide
8 Interleaved 2 of 5
Enable/Disable Interleaved 2 of 5
Parameter # 06h
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.
Parameter Menus 4 - 47
Interleaved 2 of 5
Enable/Disable Interleaved 2 of 5
Parameter # 06h
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.
*Enable Interleaved 2 of 5
(01h)
Disable Interleaved 2 of 5
(00h)
Set Lengths for Interleaved 2 of 5
Parameter # L1 = 16h L2 = 17h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for I 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page B-8.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select I 2
of 5 One Discrete Length, then scan 1, 4, to decode only I 2 of 5 symbols containing 14 characters. Numeric bar codes
begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
I 2 of 5 - One Discrete Length
NOTE When setting lengths, single digit numbers must always be preceded by a leading zero.
Set Lengths for Interleaved 2 of 5
Parameter # L1 = 16h L2 = 17h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for I 2 of
5 may be set for any length, one or two discrete lengths, or lengths within a specific range.
NOTE: When setting lengths, single digit numbers must always be preceded by a leading zero.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select I 2 of 5 One Discrete Length,
then scan 1, 4, to decode only I 2 of 5 symbols containing 14 characters. Numeric bar codes begin on page 56. To change the selection or cancel an
incorrect entry, scan Cancel on page 57.
Parameter Menus 4 - 47
Interleaved 2 of 5
Enable/Disable Interleaved 2 of 5
Parameter # 06h
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.
*Enable Interleaved 2 of 5
(01h)
Disable Interleaved 2 of 5
(00h)
Set Lengths for Interleaved 2 of 5
Parameter # L1 = 16h L2 = 17h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for I 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page B-8.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select I 2
of 5 One Discrete Length, then scan 1, 4, to decode only I 2 of 5 symbols containing 14 characters. Numeric bar codes
begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
I 2 of 5 - One Discrete Length
NOTE When setting lengths, single digit numbers must always be preceded by a leading zero.
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select I 2 of 5 Two Discrete
Lengths, then scan 0, 6, 1, 4, to decode only I 2 of 5 symbols containing 6 or 14 characters. Numeric bar codes begin on page 56. To change the
selection or cancel an incorrect entry, scan Cancel on page 57.
4 - 48 SE655 Decoded Linear Imaging Engine
Set Lengths for Interleaved 2 of 5 (continued)
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select I 2 of 5 Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only I 2 of 5 symbols containing 6 or 14 characters.
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
I 2 of 5 - Two Discrete Lengths
Length Within Range - Select this option to decode only codes within a specified range. For example, to decode I 2 of 5
symbols containing between 4 and 12 characters, first scan I 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single
digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the
selection or cancel an incorrect entry, scan Cancel on page 4-74.
I 2 of 5 - Length Within Range
Any Length - Scan this option to decode I 2 of 5 symbols containing any number of characters.
I 2 of 5 - Any Length
NOTE Selecting this option may lead to misdecodes for I 2 of 5 codes.
To Next Page
Loading...
