Philips Pocket Memo DPM8500 - I 2 of 5 Check Digit Verification; Transmit I 2 of 5 Check Digit

40 Barcode scanner configuration guide
Length Within Range - Select this option to decode only codes within a specified range. For example, to decode I 2 of 5 symbols containing between
4 and 12 characters, first scan I 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero).
Numeric bar codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57.
4 - 48 SE655 Decoded Linear Imaging Engine
Set Lengths for Interleaved 2 of 5 (continued)
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select I 2 of 5 Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only I 2 of 5 symbols containing 6 or 14 characters.
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
I 2 of 5 - Two Discrete Lengths
Length Within Range - Select this option to decode only codes within a specified range. For example, to decode I 2 of 5
symbols containing between 4 and 12 characters, first scan I 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single
digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the
selection or cancel an incorrect entry, scan Cancel on page 4-74.
I 2 of 5 - Length Within Range
Any Length - Scan this option to decode I 2 of 5 symbols containing any number of characters.
I 2 of 5 - Any Length
NOTE Selecting this option may lead to misdecodes for I 2 of 5 codes.
Any Length - Scan this option to decode I 2 of 5 symbols containing any number of characters.
NOTE: Selecting this option may lead to misdecodes for I 2 of 5 codes.
4 - 48 SE655 Decoded Linear Imaging Engine
Set Lengths for Interleaved 2 of 5 (continued)
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select I 2 of 5 Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only I 2 of 5 symbols containing 6 or 14 characters.
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
I 2 of 5 - Two Discrete Lengths
Length Within Range - Select this option to decode only codes within a specified range. For example, to decode I 2 of 5
symbols containing between 4 and 12 characters, first scan I 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single
digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the
selection or cancel an incorrect entry, scan Cancel on page 4-74.
I 2 of 5 - Length Within Range
Any Length - Scan this option to decode I 2 of 5 symbols containing any number of characters.
I 2 of 5 - Any Length
NOTE Selecting this option may lead to misdecodes for I 2 of 5 codes.
I 2 of 5 Check Digit Verification
Parameter # 31h
When enabled, this parameter checks the integrity of an I 2 of 5 symbol to ensure it complies with a specified algorithm, either USS (Uniform
Symbology Specification), or OPCC (Optical Product Code Council).
Parameter Menus 4 - 49
I 2 of 5 Check Digit Verification
Parameter # 31h
When enabled, this parameter checks the integrity of an I 2 of 5 symbol to ensure it complies with a specified algorithm,
either USS (Uniform Symbology Specification), or OPCC (Optical Product Code Council).
*Disable
(00h)
USS Check Digit
(01h)
OPCC Check Digit
(02h)
Transmit I 2 of 5 Check Digit
Parameter # 2Ch
Scan this symbol to transmit the check digit with the data.
Transmit I 2 of 5 Check Digit (Enable)
(01h)
Scan this symbol to transmit data without the check digit.
*Do Not Transmit I 2 of 5 Check Digit (Disable)
(00h)