42 Barcode scanner configuration guide
9 Discrete 2 of 5
Enable/Disable Discrete 2 of 5
Parameter # 05h
To enable or disable Discrete 2 of 5, scan the appropriate bar code below.
Parameter Menus 4 - 51
Discrete 2 of 5
Enable/Disable Discrete 2 of 5
Parameter # 05h
To enable or disable Discrete 2 of 5, scan the appropriate bar code below.
Enable Discrete 2 of 5
(01h)
*Disable Discrete 2 of 5
(00h)
Set Lengths for Discrete 2 of 5
Parameter # L1 = 14h L2 = 15h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for D 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select D
2 of 5 One Discrete Length, then scan 1, 4, to decode only D 2 of 5 symbols containing 14 characters. Numeric bar
codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
D 2 of 5 - One Discrete Length
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select D 2 of 5 Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only D 2 of 5 symbols containing 2 or 14
characters. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on
page 4-74.
D 2 of 5 - Two Discrete Lengths
Set Lengths for Discrete 2 of 5
Parameter # L1 = 14h L2 = 15h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for D 2
of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select D 2 of 5 One Discrete Length,
then scan 1, 4, to decode only D 2 of 5 symbols containing 14 characters. Numeric bar codes begin on page 56. To change the selection or cancel
an incorrect entry, scan Cancel on page 57.
Parameter Menus 4 - 51
Discrete 2 of 5
Enable/Disable Discrete 2 of 5
Parameter # 05h
To enable or disable Discrete 2 of 5, scan the appropriate bar code below.
Enable Discrete 2 of 5
(01h)
*Disable Discrete 2 of 5
(00h)
Set Lengths for Discrete 2 of 5
Parameter # L1 = 14h L2 = 15h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for D 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select D
2 of 5 One Discrete Length, then scan 1, 4, to decode only D 2 of 5 symbols containing 14 characters. Numeric bar
codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
D 2 of 5 - One Discrete Length
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select D 2 of 5 Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only D 2 of 5 symbols containing 2 or 14
characters. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on
page 4-74.
D 2 of 5 - Two Discrete Lengths
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select D 2 of 5 Two Discrete
Lengths, then scan 0, 2, 1, 4, to decode only D 2 of 5 symbols containing 2 or 14 characters. Numeric bar codes begin on page 56. To change the
selection or cancel an incorrect entry, scan Cancel on page 57.
Parameter Menus 4 - 51
Discrete 2 of 5
Enable/Disable Discrete 2 of 5
Parameter # 05h
To enable or disable Discrete 2 of 5, scan the appropriate bar code below.
Enable Discrete 2 of 5
(01h)
*Disable Discrete 2 of 5
(00h)
Set Lengths for Discrete 2 of 5
Parameter # L1 = 14h L2 = 15h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for D 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select D
2 of 5 One Discrete Length, then scan 1, 4, to decode only D 2 of 5 symbols containing 14 characters. Numeric bar
codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
D 2 of 5 - One Discrete Length
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select D 2 of 5 Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only D 2 of 5 symbols containing 2 or 14
characters. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on
page 4-74.
D 2 of 5 - Two Discrete Lengths
Length Within Range - Select this option to decode codes within a specified range. For example, to decode D 2 of 5 symbols containing between 4
and 12 characters, first scan D 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers must be preceded by a leading zero). Numeric
bar codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57.
4 - 52 SE655 Decoded Linear Imaging Engine
Set Lengths for Discrete 2 of 5 (continued)
Length Within Range - Select this option to decode codes within a specified range. For example, to decode D 2 of 5
symbols containing between 4 and 12 characters, first scan D 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single
digit numbers must be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the selection or
cancel an incorrect entry, scan Cancel on page 4-74.
D 2 of 5 - Length Within Range
Any Length - Scan this option to decode D 2 of 5 symbols containing any number of characters.
D 2 of 5 - Any Length
NOTE Selecting this option may lead to misdecodes for D 2 of 5 codes.
Any Length - Scan this option to decode D 2 of 5 symbols containing any number of characters.
To Next Page
Loading...
