49Barcode scanner configuration guide
13 Codabar
Enable/Disable Codabar
Parameter # 07h
To enable or disable Codabar, scan the appropriate bar code below.
4 - 58 SE655 Decoded Linear Imaging Engine
Codabar
Enable/Disable Codabar
Parameter # 07h
To enable or disable Codabar, scan the appropriate bar code below.
Enable Codabar
(01h)
*Disable Codabar
(00h)
Set Lengths for Codabar
Parameter # L1 = 18h L2 = 19h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for Codabar may be set for any length, one or two discrete lengths, or lengths within a specific range. To
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
Codabar One Discrete Length, then scan 1, 4, to decode only Codabar symbols containing 14 characters. Numeric bar
codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Codabar - One Discrete Length
Two Discrete Lengths - This option sets the unit to decode only those codes containing two selected lengths. For
example, select Codabar Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only Codabar symbols containing 6 or
14 characters. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel
on page 4-74.
Set Lengths for Codabar
Parameter # L1 = 18h L2 = 19h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for
Codabar may be set for any length, one or two discrete lengths, or lengths within a specific range.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select Codabar One Discrete Length,
then scan 1, 4, to decode only Codabar symbols containing 14 characters. Numeric bar codes begin on page 56. To change the selection or cancel
an incorrect entry, scan Cancel on page 57.
4 - 58 SE655 Decoded Linear Imaging Engine
Codabar
Enable/Disable Codabar
Parameter # 07h
To enable or disable Codabar, scan the appropriate bar code below.
Enable Codabar
(01h)
*Disable Codabar
(00h)
Set Lengths for Codabar
Parameter # L1 = 18h L2 = 19h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for Codabar may be set for any length, one or two discrete lengths, or lengths within a specific range. To
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
Codabar One Discrete Length, then scan 1, 4, to decode only Codabar symbols containing 14 characters. Numeric bar
codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Codabar - One Discrete Length
Two Discrete Lengths - This option sets the unit to decode only those codes containing two selected lengths. For
example, select Codabar Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only Codabar symbols containing 6 or
14 characters. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel
on page 4-74.
Two Discrete Lengths - This option sets the unit to decode only those codes containing two selected lengths. For example, select Codabar Two
Discrete Lengths, then scan 0, 2, 1, 4, to decode only Codabar symbols containing 6 or 14 characters. Numeric bar codes begin on page 56. To
change the selection or cancel an incorrect entry, scan Cancel on page 57.
Parameter Menus 4 - 59
Codabar (continued)
Codabar - Two Discrete Lengths
Length Within Range - Select this option to decode a code within a specified range. For example, to decode Codabar
symbols containing between 4 and 12 characters, first scan Codabar Length Within Range, then scan 0, 4, 1 and 2
(single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the
selection or cancel an incorrect entry, scan Cancel on page 4-74.
Codabar - Length Within Range
Any Length - Scan this option to decode Codabar symbols containing any number of characters.
Codabar - Any Length
Length Within Range - Select this option to decode a code within a specified range. For example, to decode Codabar symbols containing between 4
and 12 characters, first scan Codabar Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero).
Numeric bar codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57.
Parameter Menus 4 - 59
Codabar (continued)
Codabar - Two Discrete Lengths
Length Within Range - Select this option to decode a code within a specified range. For example, to decode Codabar
symbols containing between 4 and 12 characters, first scan Codabar Length Within Range, then scan 0, 4, 1 and 2
(single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the
selection or cancel an incorrect entry, scan Cancel on page 4-74.
Codabar - Length Within Range
Any Length - Scan this option to decode Codabar symbols containing any number of characters.
Codabar - Any Length
Any Length - Scan this option to decode Codabar symbols containing any number of characters.
To Next Page
Loading...
