51Barcode scanner configuration guide
14 MSI
Enable/Disable MSI
Parameter # 0Bh
To enable or disable MSI, scan the appropriate bar code below.
Parameter Menus 4 - 61
MSI
Enable/Disable MSI
Parameter # 0Bh
To enable or disable MSI, scan the appropriate bar code below.
Enable MSI
(01h)
*Disable MSI
(00h)
Set Lengths for MSI
Parameter # L1 = 1Eh L2 = 1Fh
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes check digits. Lengths for MSI
can be set for any length, one or two discrete lengths, or lengths within a specific range.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select MSI - One Discrete Length, then
scan 1, 4, to decode only MSI symbols containing 14 characters. Numeric bar codes begin on page 56. To change the selection or cancel an incorrect
entry, scan Cancel on page 57.
4 - 62 SE655 Decoded Linear Imaging Engine
Set Lengths for MSI
Parameter # L1 = 1Eh L2 = 1Fh
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes
check digits. Lengths for MSI can be set for any length, one or two discrete lengths, or lengths within a specific range. See
Table B-5 on page B-9 for ASCII equivalents. To set lengths via serial commands, see Setting Code Lengths Via Serial
Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
MSI - One Discrete Length, then scan 1, 4, to decode only MSI symbols containing 14 characters. Numeric bar codes
begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
MSI - One Discrete Length
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select MSI - Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only MSI symbols containing 6 or 14 characters.
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
MSI - Two Discrete Lengths
Length Within Range - Select this option to decode codes within a specified range. For example, to decode MSI symbols
containing between 4 and 12 characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit
numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the selection or
cancel an incorrect entry, scan Cancel on page 4-74.
MSI - Length Within Range
Any Length - Scan this option to decode MSI Plessey symbols containing any number of characters.
MSI - Any Length
NOTE Selecting this option may lead to misdecodes for MSI codes.
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select MSI - Two Discrete
Lengths, then scan 0, 6, 1, 4, to decode only MSI symbols containing 6 or 14 characters. Numeric bar codes begin on page 56. To change the
selection or cancel an incorrect entry, scan Cancel on page 57.
4 - 62 SE655 Decoded Linear Imaging Engine
Set Lengths for MSI
Parameter # L1 = 1Eh L2 = 1Fh
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes
check digits. Lengths for MSI can be set for any length, one or two discrete lengths, or lengths within a specific range. See
Table B-5 on page B-9 for ASCII equivalents. To set lengths via serial commands, see Setting Code Lengths Via Serial
Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
MSI - One Discrete Length, then scan 1, 4, to decode only MSI symbols containing 14 characters. Numeric bar codes
begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
MSI - One Discrete Length
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select MSI - Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only MSI symbols containing 6 or 14 characters.
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
MSI - Two Discrete Lengths
Length Within Range - Select this option to decode codes within a specified range. For example, to decode MSI symbols
containing between 4 and 12 characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit
numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the selection or
cancel an incorrect entry, scan Cancel on page 4-74.
MSI - Length Within Range
Any Length - Scan this option to decode MSI Plessey symbols containing any number of characters.
MSI - Any Length
NOTE Selecting this option may lead to misdecodes for MSI codes.
Length Within Range - Select this option to decode codes within a specified range. For example, to decode MSI symbols containing between 4 and 12
characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar
codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57.
4 - 62 SE655 Decoded Linear Imaging Engine
Set Lengths for MSI
Parameter # L1 = 1Eh L2 = 1Fh
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes
check digits. Lengths for MSI can be set for any length, one or two discrete lengths, or lengths within a specific range. See
Table B-5 on page B-9 for ASCII equivalents. To set lengths via serial commands, see Setting Code Lengths Via Serial
Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
MSI - One Discrete Length, then scan 1, 4, to decode only MSI symbols containing 14 characters. Numeric bar codes
begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
MSI - One Discrete Length
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select MSI - Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only MSI symbols containing 6 or 14 characters.
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
MSI - Two Discrete Lengths
Length Within Range - Select this option to decode codes within a specified range. For example, to decode MSI symbols
containing between 4 and 12 characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit
numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the selection or
cancel an incorrect entry, scan Cancel on page 4-74.
MSI - Length Within Range
Any Length - Scan this option to decode MSI Plessey symbols containing any number of characters.
MSI - Any Length
NOTE Selecting this option may lead to misdecodes for MSI codes.
Any Length - Scan this option to decode MSI Plessey symbols containing any number of characters.
To Next Page
Loading...
