Philips Pocket Memo DPM8500 - MSI Check Digits; Transmit MSI Check Digit; MSI Check Digit Algorithm

52 Barcode scanner configuration guide
NOTE: Selecting this option may lead to misdecodes for MSI codes.
4 - 62 SE655 Decoded Linear Imaging Engine
Set Lengths for MSI
Parameter # L1 = 1Eh L2 = 1Fh
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes
check digits. Lengths for MSI can be set for any length, one or two discrete lengths, or lengths within a specific range. See
Table B-5 on page B-9 for ASCII equivalents. To set lengths via serial commands, see Setting Code Lengths Via Serial
Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
MSI - One Discrete Length, then scan 1, 4, to decode only MSI symbols containing 14 characters. Numeric bar codes
begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
MSI - One Discrete Length
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select MSI - Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only MSI symbols containing 6 or 14 characters.
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
MSI - Two Discrete Lengths
Length Within Range - Select this option to decode codes within a specified range. For example, to decode MSI symbols
containing between 4 and 12 characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit
numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the selection or
cancel an incorrect entry, scan Cancel on page 4-74.
MSI - Length Within Range
Any Length - Scan this option to decode MSI Plessey symbols containing any number of characters.
MSI - Any Length
NOTE Selecting this option may lead to misdecodes for MSI codes.
MSI Check Digits
Parameter # 32h
These check digits at the end of the bar code verify the integrity of the data. At least one check digit is always required. Check digits are not
automatically transmitted with the data.
Parameter Menus 4 - 63
MSI Check Digits
Parameter # 32h
These check digits at the end of the bar code verify the integrity of the data. At least one check digit is always required.
Check digits are not automatically transmitted with the data.
*One MSI Check Digit
(00h)
If two check digits are selected, also select an MSI Check Digit Algorithm on page 4-64.
Two MSI Check Digit
(01h)
Transmit MSI Check Digit
Parameter # 2Eh
Scan this symbol to transmit the check digit with the data.
Transmit MSI Check Digit (Enable)
(01h)
Scan this symbol to transmit data without the check digit.
*Do Not Transmit MSI Check Digit (Disable)
(00h)
If two check digits are selected, also select an MSI Check Digit Algorithm.
Parameter Menus 4 - 63
MSI Check Digits
Parameter # 32h
These check digits at the end of the bar code verify the integrity of the data. At least one check digit is always required.
Check digits are not automatically transmitted with the data.
*One MSI Check Digit
(00h)
If two check digits are selected, also select an MSI Check Digit Algorithm on page 4-64.
Two MSI Check Digit
(01h)
Transmit MSI Check Digit
Parameter # 2Eh
Scan this symbol to transmit the check digit with the data.
Transmit MSI Check Digit (Enable)
(01h)
Scan this symbol to transmit data without the check digit.
*Do Not Transmit MSI Check Digit (Disable)
(00h)
Transmit MSI Check Digit
Parameter # 2Eh
Scan this symbol to transmit the check digit with the data.
Parameter Menus 4 - 63
MSI Check Digits
Parameter # 32h
These check digits at the end of the bar code verify the integrity of the data. At least one check digit is always required.
Check digits are not automatically transmitted with the data.
*One MSI Check Digit
(00h)
If two check digits are selected, also select an MSI Check Digit Algorithm on page 4-64.
Two MSI Check Digit
(01h)
Transmit MSI Check Digit
Parameter # 2Eh
Scan this symbol to transmit the check digit with the data.
Transmit MSI Check Digit (Enable)
(01h)
Scan this symbol to transmit data without the check digit.
*Do Not Transmit MSI Check Digit (Disable)
(00h)
Scan this symbol to transmit data without the check digit.
Parameter Menus 4 - 63
MSI Check Digits
Parameter # 32h
These check digits at the end of the bar code verify the integrity of the data. At least one check digit is always required.
Check digits are not automatically transmitted with the data.
*One MSI Check Digit
(00h)
If two check digits are selected, also select an MSI Check Digit Algorithm on page 4-64.
Two MSI Check Digit
(01h)
Transmit MSI Check Digit
Parameter # 2Eh
Scan this symbol to transmit the check digit with the data.
Transmit MSI Check Digit (Enable)
(01h)
Scan this symbol to transmit data without the check digit.
*Do Not Transmit MSI Check Digit (Disable)
(00h)