Unit:mm
30
30
25.2
40.3
15
21
9
6
25.2
F3:G1/8"(BSPP), M5
Hex flat 12
20
20
*1.Hysteresis value is adjustable within 1 ~ 8 digits for one point set mode and window comparator mode.
0.001
0.001
0.01
0.1
1
0.1
kPa
kgf/cm
2
bar
psi
mmHg
inHg
300 kPa
(Vacuum)
MODEL
Rated pressure range
Set pressure range
Withstand pressure
Fluid
Filtered air, Non-corrosive / Non-flammable gas
Power supply voltage
Current consumption
Switch output
Repeatability(Switch output)
Hysteresis mode
Response time
Output short circuit protection
Indicator accuracy
Switch on indicator
Enclosure
Vibration
Shock
Temperature characteristic
Port size
Lead wire
Weight
12 to 24V DC ±10%, Ripple (P-P) 10% or less
≤ 40mA (With no load)
PNP: open collector 2 outputs
Max. load current: 125mA
Max. supply voltage: 24V DC
Residual voltage: ≤ 1.5V
±0.2% F.S. ±1 digit
≤ 2.5ms
(chattering-proof function: 25ms, 100ms, 250ms,
500ms, 1000ms and 1500ms selections)
Yes
±2% F.S. ±1 digit (ambient temperature: 25 ±3°C)
Orange Indicator 1 : OUT1 & Orange Indicator 2 : OUT2
IP 40
Operation: 0 ~ 50°C, Storage:-10 ~ 60°C
( No condensation or freezing)
Operation/Storage: 35 ~ 85% RH ( No condensation)
1000V AC in 1-min (between case and lead wire)
50MΩ (at 500V DC, between case and lead wire)
Total amplitude 1.5mm or 10G,10Hz-55Hz-10Hz scan
for 1 minute, two hours each direction of X, Y and Z
100m/s
2
(10G), 3 times each in direction of X, Y and Z
±2.5% F.S. of detected pressure (25°C) at temp. Range of 0~50°C
F3: G1/8"(BSPP), M5
Ø4 Oil-resistance cable ( PVC ) - 26 AWG ( 0.15 mm² ) - 5 cores
Approx. 80g
(With 2 meter cable and M8 4Pin male QD connector)
10.0 ~ -101.3 kPa
0.0 ~ -101.3 kPa
Set pressure
resolution
One point set mode
Window
comparator mode
Hysteresis
Adjustable (*1)
Display
3 ½ digital, 7 segment LCD display ( Red / Green / Orange )
( Sampling rate : 5 times / sec. )
Ambient temp.
Range
Ambient humidity
range
Withstand
voltage
Insulation
resistance
Environment
P43V-04-F3-QD
SET
Lock Indicator
( )Button Setting
Button
( )Button
2 Color Main Display
Setting Mode
Sub-display Section
Output 1 Indicator
Output 2 Indicator
mmHginHgpsibarkgfMPakPa
Pressure Unit
Display Section
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
ON:Green
OFF:Red
ON:Red
OFF:Green
ON/ OFF:
Green
ON/ OFF:
Red
SET
SET
SET
SET
2.5ms
25ms 100ms 250ms
500ms
1000ms1500ms
SET
(inHg) (mmHg)
(kPa)
(kgf/cm
2
)
(bar)
(psi)
Measure mode
Response time setting
Unit setting
Display color setting
OUT 1
Operating mode setting
OUT 1
type setting
Press button for more than 3 seconds.
kPa
kPa
kPa
kPa
kPa
kPa
(oPS)
One point set
mode
Window comparator
mode
Hysteresis
mode
Use the or button to set OUT1 operating mode.
Use the or button to set OUT1 type.
NC modeNO mode
OUT 2
Operating mode setting
SET
Use the or button to set OUT2 operating mode.
Window comparator
mode
Hysteresis
mode
(oPS)
One point set
mode
oFF mode
OUT 2
type setting
(*1 )
Use the or button to select response time.
Use the or button to set display color.
Use the or button to set desired pressure unit.
Measure mode
NC modeNO mode
【NOTE :】
*1. This setting mode will not display when output 2 is set to oFF.
SET
Use the or button to set OUT2 type.
kPa
kPa
kPa
Piab AB
P.O. Box 146
SE-18212 DANDERYD
SWEDEN
Each unit is identified by a label with identification information. For any communication with
Piab AB or service centers always refer to the label information.
Vacuum switch 3-colour digital display M8
PR-0525C 2022/10 Printing We reserve the right to change the specification without prior notice.
1 Manufacturer
2 Safety Instructions
1.1 Identification Label
Model number : P43V-04-F3-QD
Item number : 0212040
Warning !
Vacuum force
Warning !
1.2 Model Numbers
2.1 General Safety
2.2 Safe Usage
2.3 Compliance
■ 2.2.1 Assembly and Maintenance
Wear eye protection
Warning !
Exhaust
Warning !
Unrestricted
exhaust
The correct use of pneumatic equipment within a system is the responsibility of the system
designer or the person who determines its technical specifications.
The use of safety guards is recommended to minimize the risk of injury to persons; pay
close attention to the fact that compressed air may lead to explosion of closed containers,
and vacuum may lead to the implosion of closed containers.
In the event that, contrary to indications, dusts, oil mists, fumes, etc. are suctioned, these
will be mixed with the discharge air of the vacuum generator and expelled via the discharge
conduit; use suitable, approved air filters to avoid possible intoxications.
Ensure that the components are properly secured; regularly check that connections are in
good working order, as high cycles or vibrations may cause them to loosen.
Unit:mm
Mounting bracket
BT-12
Mounting bracket
BT-1
3
BT-12
BT-13
20
5
4.2
29.5
20
20
45
202
45
13
2
20
20
29.5
20
4.2
5
M3
M3
14
14
Caution !
3.2 Mounting
3 Installation
3.1 Unpacking
4 Specifications
4.1 Specifications
When unpacking check that the product is complete and undamaged. The manual should
be stored for future reference.
4.3 Ordering Information
European Directives, CE
Electromagnetic Compatibility (EMC)
Standard reference:
EN/(IEC) 61000-6-2:2005 EN/(IEC) 61000-6-4:2007+A1
RoHS2 Directive (2011/65/EU)
UK Legislation, UKCA
Electromagnetic Compatibility (EMC)
Standard reference:
BS EN/(IEC) 61000-6-2:2005 BS EN/(IEC) 61000-6- 4:2007+A1
UK Legislation-The Restriction of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment Regulations 2012
Do not use compressed air pressure or electrical voltage outside the specification due to risk
of ejected objects and/or damage of product and/or application failure.
Do not install or operate your product if it is damaged during transport, handling or use.
Damage may result in bursting and cause injury or property damage.
Do not use corrosive or flammable gas or liquid with this product.
Do not drop, hit or allow excessive shock. Even if switch body appears undamaged, internal
components may be broken and can cause malfunction.
Turn power off before connecting wiring. Wrong wiring or short circuit will damage and/or
cause malfunction.
Do not use in environment containing steam or oil vapor.
This product is not explosion-proof rated. Do not use in atmosphere containing flammable
or explosive gases.
Wiring for pressure sensor should avoid power source line and high voltage line. If use in the
same circuit, noise may cause malfunction.
Warning !
Compressed air may be dangerous if used by unskilled personnel. Assembling, using and
maintaining the product should solely be carried out by experienced and specially trained
personnel. Prior to assembly and disassembly of the components, cut off voltage and
pressure and discharge residual pressure. Install and maintain the components only after
thoroughly reading and understanding this manual.
■ 2.2.2 Intended Use
●
●
For professional use only.
The safety instructions shall be followed.
The product is used to sense pressure in vacuum systems.
The product shall be used in environments within the product’s specifications and
certifications.
The product shall be installed in accordance to installation instructions.
●
●
●
●
●
■ 2.2.3 Misuse
Do not install or use the product if it is damaged.
Do not use compressed air pressure or electrical voltage outside the specification (operation
voltage ± 10%).
Do not use the equipment as a stand-alone unit to fulfill international lifting standards.
Do not use compressed air pressure or electrical voltage outside the specification.
●
●
●
●
●
●
●
●
●
●
When mounting, always use the wrench on the metallic area near the pressure port. Never
apply a wrench to the plastic body, it will damage the sensor.
Over tightening may cause damages to the port thread, mounting bracket and pressure
sensor. Under tightening may result loosen or leakage.
Apply pressure and power after installation and make necessary adjustments and inspect
any possible signs of leakage to ensure proper installation.
●
●
●
Wear ear protection
4.2 Output Circuit Wiring Diagrams
4.4 Panel Description
4.5 Dimensions
4.6 Initial Setting Mode
2 PNP+Copy function
RL
RL
Copy function
(Orange)
Main circuit
DC (-) (Blue)
DC (+) (Brown)
OUT2(White)
OUT1(Black)
V：Vacuum (10.0~-101.3kPa)
F3：G1/8”(BSPP), M5
Pressure Range
Pressure Port
QD：With 2 meter cable and M8 4Pin male QD connector
Cable Length / Connector
Output Specifications
Optional Parts
BT-12：Mounting bracket
BT-13：Mounting bracket
P43V-04-F3-QD
04 ：2 PNP+Copy function
To Next Page
General