Page 4 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 64254
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
G&&7%P#*%,89%O,(*
a. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against the body
is unstable and can lead to loss of control.
b. U&%8&$%2&(4*%$.*%$&&71 Use the correct tool for the
application. The correct tool will do the job better
and safer at the rate for which the tool is designed.
c. U&%8&$%'#*%$.*%$&&7%"2%$.*%G("33*(%9&*#%8&$%
$'(8%$.*%$&&7%&8%&(%&221 Any tool that cannot
be controlled with the Trigger is dangerous
and must not be used until repaired.
d. U"#4&88*4$%$.*%$&&7%2(&5%$.*%,"(%#&'(4*%
+*2&(*%5,Y"83%,9Z'#$5*8$#=%9&"83%$&&7%
5,"8$*8,84*=%47*,("83%Z,5#=%$&'4."83%$.*%
Q&(Y/"*4*%O&8$,4$=%7*,]"83%)&(Y%,(*,=%7&,9"83=%
&(%'87&,9"83%$.*%$&&71 Such precautionary
measures reduce the risk of injury to persons.
e. Store the tool when it is idle out of reach
of children and other untrained persons.
A tool is dangerous in the hands of untrained users.
f. N,"8$,"8%$.*%$&&7%)"$.%4,(*1
A properly maintained tool reduces the
risk of binding and is easier to control.
g. O.*4Y%2&(%5"#,7"385*8$%&(%+"89"83%&2%5&]"83%
/,($#=%+(*,Y,3*%&2%/,($#=%,89%,8[%&$.*(%4&89"$"&8%
$.,$%,22*4$#%$.*%$&&7_#%&/*(,$"&81 If damaged, have
the tool serviced before using. Many accidents
are caused by poorly maintained tools.
There is a risk of bursting if the tool is damaged.
h. P#*%&87[%,44*##&("*#%$.,$%,(*%"9*8$"2"*9%+[%$.*%
5,8'2,4$'(*(%2&(%$.*%#/*4"2"4%$&&7%5&9*71 Use of
an accessory not intended for use with the specific
tool model, increases the risk of injury to persons.
i. P#*%&87[%$.&#*%2,#$*8*(#%7"#$*9%"8%$.*%
E/*4"2"4,$"&8#%4.,($%&2%$."#%5,8',71
Fasteners%not identified for use with this tool by the
tool manufacturer are able to result in a risk of injury
to persons or tool damage when used in this tool.
E*(]"4*
a. Tool service must be performed only
by qualified repair personnel.
b. Q.*8%#*(]"4"83%,%$&&7=%'#*%&87[%"9*8$"4,7%
(*/7,4*5*8$%/,($#1%P#*%&87[%,'$.&("`*9%/,($#1
c. P#*%&87[%$.*%7'+("4,8$#%#'//7"*9%)"$.%$.*%
$&&7%&(%#/*4"2"*9%+[%$.*%5,8'2,4$'(*(1
F"(%E&'(4*
a. M*]*(%4&88*4$%$&%,8%,"(%#&'(4*%$.,$%
"#%4,/,+7*%&2%*\4**9"83%abb%JEL1
Over pressurizing the tool may cause
bursting, abnormal operation,
breakage of the tool or serious injury
to persons. Use only clean, dry, regulated
compressed air at the rated pressure or within the
rated pressure range as marked on the tool. Always
verify prior to using the tool that the air source has
been adjusted to the rated air pressure or within the
rated air-pressure range.
b. Never use oxygen, carbon dioxide, combustible
gases or any bottled gas as an air source
for the tool. Such gases are capable of
explosion and serious injury to persons.
%EF!6%GW6E6%LMEGKPOGLIME1
To Next Page
Loading...