Initial Operation
We recommend letting the locomotive
run without a train for 30 minutes
in both directions, to properly break
it in. This will help achieve optimal
performance and longevity for the
locomotive. Of course, your model
should only be run on smooth and
perfectly clean tracks with reliable
electrical contact to all track
sections.
Smoke Unit Operation and Care
Drop about 10 to 20 drops of smoke
fluid into the top of the smokestack.
If over-filled, the smoke generator
will not work. Turn the loco upside
down to drain out excess smoke fluid.
Never insert any object down into the
smokestack. The heating element in
the center of the stack is delicate and
easily broken by foreign objects. Use
only PIKO smoke fluid to preserve the
life of the smoke generator. There is
no harm in leaving smoke fluid in the
smoke generator or in letting the the
loco run without fluid in the smoke
generator.
Technical Data
Power Supply
The model should only be operated
on a pure, filtered DC power supply
of 0 to 24 volts, with a capacity of
2 - 5 Amp and a fast-acting fuse or
circuit breaker to protect against short
circuits. Do not use a power supply
which is not in safe and perfect
working condition. (See “Digital
Decoder” instruction for operation on
digital power.)
Drive System
The model contains 2 high capacity
motors, that are connected through
robust gearing to 4 axles.
Lighting
The model is equipped with an
automatic directional headlight, using
white LEDs for a realistic appearance.
The “front” lights are illuminated
according to the travel direction.
Engine lighting switchable via
function key or switch.
Precautions and Recommendations
Minimum Radius
The locomotive can run on tracks with
a radius of 600 mm (23.62“). Due to
the design a minimum radius of 920
mm (36.28“) is recommended. Natu-
rally, extended operation on small
radius curves leads to greatly increa-
sed wear of the locomotive and track.
Digital Decoder
The model is factory fitted with the
PIKO locomotive decoder #36125.
The locomotive can be used on both
digital and analoge systems.
Sound
The model is factory equipped with sound
module #36228.
The sound module
contains a full range speaker with a
waterproof membrane. This sound can be
used both in analog and digital mode.
#35268 Track switch magnet
In the locomotive there is a sensor (reed
contact),which reacts to every track
switching magnet #35268 and triggers
either whistle or bell.
Maintenance
Lubrication
After each 25 hours of operation, and
after any long periods of storage, please
lubricate the locomotive‘s gears with a
sparing amount of plastic-compatible,
non-hardening grease
(e. g. Lubricating
Grease PIKO no. # 36216)
.
Cleaning
If cleaning is necessary, use only a mild
cleaning agent (such as soap and water)
and gentle action with a soft non-
abrasive cloth or brush. Never immerse
the loco in liquid or “flood” any internal
parts!
Normal Wear Items
Electrical pick-up shoes, wheel wipers
and traction tires will wear with use
and should be replaced as needed.
Please Note! Damage to Carpets and
Other Surfaces: Normal operation of the
locomotive causes wear of mechanical
parts (wheels, electrical pickups etc.). This
produces carbonized dust, grease and
oil, which can permanently stain carpets,
wood floors and other materials. It is
the user’s responsibility to take proper
precautions against this damage. Wipe
any grease or oil from the track rails with
a clean soft cloth. PIKO Spielwaren GmbH,
as well as its representatives, distributors
and retailers, assume no liability for any
such damage.
Please Note!
Important Safety Precautions
• Check the power supply regularly for any
damage or problems.
• Do not use a malfunctioning or damaged
power supply!
• This model must only be operated with
one power source per circuit!
• This product is not a toy, not suitable for
personnel under 14 years of age. This
product has small parts, sharp parts, and
moving parts.
• This model must only be operated with a
safety-assured power supply with the
identification!
• The power supply is not a toy!
• Disconnect the model from the power
supply before cleaning or servicing!
• Do not insert the track power connecting
wires into household “mains” voltage
outlets.
5
To Next Page
Loading...
