PIKO SmartDecoder XP 5.1 Next18 User Manual

Function outputs in analog mode
It is possible to program the decoder so that function keys F0 - F12 (as they are assigned in the function mapping)
can also be activated in analog mode. To do this, CVs 13 & 14 must rst be programmed with a DCC central control
unit. The corresponding values can be found in the CV table of the detailed operating instructions. The light function
F0 is factory-set to “on.”
Motorola
®
The decoder utilizes 4 Motorola® addresses to access functions F1 - F 16, when using a Motorola—based
command station. The three sequence addresses for the functions F5 - F16 are ascending to the decoder address
and can be activated in CV61 as required by the values 1 (F5 - F8), 2 (F5 - F12), or 3 (F5 - F16).
Conguration of CVs
In addition to the decoder address, the indexed CVs of a locomotive decoder are the most important CVs. These are
the CVs 12 and 29 in the PIKO SmartDecoder XP 5.1. As a rule, an indexed CV contains various basic settings of
a decoder, such as reversing the direction of travel. CV calculation examples can be found in the detailed operating
instructions.
RailCom
®
, RailCom Plus
®
In the decoder, CV29 (RailCom®) can be turned on or off via bit 3. If RailCom Plus® is turned on, the decoder
will be automatically recognized by a RailCom Plus®-enabled DCC control system (i.e. PIKO SmartControl) and
a locomotive icon, decoder name, and its special function icons will appear on the control system’s screen. With
RailCom Plus® technology, no locomotive data has to be stored in the DCC central control unit and no locomotive
addresses have to be programmed into the decoder.
Braking
The decoder understands the following braking methods:
Märklin® braking section (brakes with analog DC voltage)
DCC braking function
ABC (Automatic Brake Control) braking section
The decoder can stop the model with two adjustable braking distances that are accurate down to the centimeter.
More information on "braking behavior" can be found in the detailed operating instructions.
Function outputs
A comprehensive description of all options related to the function outputs can be found in the detailed operating instructions.
Simple and extended function mapping
Easy-to-use function mapping allows you to assign functions like lighting and other outputs to any key between
F0 – F12. Acceleration, braking delay, and switching (shunting) mode can be assigned to any function keys using
CVs 156 and 157.
Smoke generator control
A smoke generator with a maximum current consumption of 250mA can be connected to the outputs A1 and A2,
which is controlled by the decoder load-dependently. Function key assignment is done using extended function
mapping.
Extended function mapping
Due to its complex nature, extended function mapping cannot easily be set by programming individual CVs. To
work with extended function mapping, you will need the PIKO SmartProgrammer device (#56415) and, if desired,
the PIKO SmartTester (#56416). Detailed information on extended function mapping is available in the instruction
manual.
Servo control
The decoder can control up to two servo motors via outputs A1, A2. Function key assignment is done exclusively via
extended function mapping.
The use of a servo with the decoder requires electronics expertise.
Further information can be found in the detailed operating instructions.
ATTENTION: Soldering on the decoder should only be carried out by experienced specialists with the appropriate tools.
Decoders damaged by improper handling will not be covered by the warranty.
Factory reset
To restore the decoder to its factory settings, program CV8 to a value of 8.
Programming
Conguration variables (CVs) form the basis of all the decoder’s settings. This decoder can be used with the PIKO
SmartControllight DCC system, the PIKO SmartControl DCC system, or any other DCC- and Motorola based systems.
For more information on programming options, please refer to the instruction manual.
Märklin® is a registered trademark of Gebr. Märklin & Cie. GmbH, Göppingen
Motorola® is a registered trademark of Motorola Inc. Tempe, (Phoenix) Arizona / USA
RailComPlus® is a registered trademark of Lenz Elektronik GmbH
Service:
Internet: www.piko.de
E-Mail:info@piko.de
In the event of a defective decoder, please return the decoder module to PIKO along with proof of purchase, the decoder
address, and a short description of the problem.
Warranty Statement
Each decoder module is fully tested before shipment. Nevertheless, should a malfunction occur within the 2-year warranty
period, we will repair the module free of charge on presentation of the proof of purchase. This warranty is voided if the unit
has been damaged by improper use. Please note that, according to the German Electromagnetic Compatibility Law (EMV-
Gesetz), the decoder module may only be used inside models bearing the CE mark.
Product subject to changes. All rights reserved. Printed 01/2022.
Copy and duplication of this text are permissible only with the permission of the publisher.

PIKO SmartDecoder XP 5.1 Next18 Specifications

General

Brand	PIKO
Model	SmartDecoder XP 5.1 Next18
Category	Control Unit
Language	English