Pilz PSEN sc ME 5.5 08-17 - Page 112

Pilz PSEN sc ME 5.5 08-17

131 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Dimensions

Operating Manual PSEN sc ME 5.5 08-17

1005388-EN-01

| 112

Slave unit

49

59.5

77.6

152

M5x8(4x)

112.5

Side view Plan view

77.6

73

102

M5x10 (2x)

Rear view View from below with protective cover

Table of Contents

Default Chapter3
- Table of Contents3
1 Introduction7
- Validity of Documentation7
- Using the Documentation7
- Definition of Symbols7
2 Overview9
- Device Features9
- Unit View10
3 Safety12
- Intended Use12
- Safety Regulations13
- Safety Assessment13
- Use of Qualified Personnel13
- Warranty and Liability13
- Disposal13
- For Your Safety14
4 Function Description15
- Basic Function of the Safety Laser Scanner15
- Single Connection15
- Series Connection16
- Stationary and Mobile Danger Zone17
- Horizontal Application19
- Vertical Application19
- Mobile Application20
- Reference Outline Monitoring20
- Use of Zone Sets and Switching of Zone Sets20
- Automatic and Monitored Start/Restart21
- Manual Restart22
- Ossd22
- Reset22
- Encoder23
- Coding against Interference23
- Edm23
- Wave24
- Rest Condition24
- Muting25
- Override26
- Multiple Evaluation27
- Restore Configuration (Fast Replacement)27
- Report Generation27
5 Project Configuration28
- Maintaining the Safety Distance28
- General28
- Horizontal Application with Stationary Danger Zone29
- Horizontal Application with Automated Guided Vehicle Systems31
- Vertical Application33
- Calculation of the Overall Response Time34
- Switching of Zone Sets34
- Monitoring of Reference Outlines35
- Area with Limited Detection Capability37
- Installation of Several Adjacent Safety Laser Scanners38
- Ambient Conditions39
- Dust Filtration40
- Distance to Intense Light Sources and to Reflective Surfaces40
- Distance from Walls42
- Planning of Safety and Warning Zones and Zone Sets42
- Switchover Time with Zone Selection42
- Encoder42
- Determining the Moment of Switchover44
- Muting45
- General45
- Muting in Two Directions46
- Muting in One Direction49
- Dynamic Muting51
- Override52
- Rest Condition53
6 Wiring54
- General Guidelines54
- Connector Assignment Master Unit54
- Connector Assignment Slave Unit57
- Configurable Inputs/Outputs57
- Configurable Inputs57
- Wiring of the Configurations58
- Connect Supply Voltage and Safety Controller58
- Connection to Psenscan Configurator60
- Single Connection61
- Series Connection62
- Connections for Muting Sensors63
7 Installation and Alignment64
- Installation Options64
- Installation Without PSEN Sc Bracket H64
- Installation of the Protective Bracket PSEN Sc Bracket H at the Safety Laser Scanner65
- Installation on the Floor66
- Installation with Setting of Angle of Inclination/Roll Angle - Bracket PSEN Sc Bracket PR66
- Installation with Angle of Inclination Setting - Holder PSEN Sc Bracket P69
- Set the Angle of Inclination of the Safety Laser Scanner69
- Set the Side Inclination of the Safety Laser Scanner70
- Measures to Safeguard Unsecured Areas71
8 Psenscan Configurator73
- Basics73
- Installation73
- System Requirements73
- Install Psenscan Configurator73
- Ethernet Connections74
- Factory Default Settings for the IP Addresses74
- Create Firewall Rule74
- Connect Automatically74
- Download Configuration to Device75
- Create Backup Copy of a Configuration75
- Manage Password76
- Reset Password76
9 First Commissioning77
- Requirements for Commissioning77
- System Connection77
- Configuration of Zones78
- Example for an 8-Pin Connection79
- Example for a 17-Pin Connection82
- Example for a 17+8-Pin Connection86
- Example for a 17+8-Pin Connection with Encoder Inputs90
- Testing94
10 Operation96
- Display of the Monitoring Status96
- Display During Normal Operation96
- Diagnostic Information98
- Error98
- Warnings100
- Information101
- Log File101
- Text Messages in the Display102
- Restore Configuration103
- Reset104
- Activate Rest Condition105
- Deactivate Rest Condition105
11 Safety Checks, Maintenance and Repair106
- Cleaning106
- Checks107
- Regular Check107
- Check after Plant/Machine Modification107
- Maintenance107
- Exchange PSEN Sc Head107
12 Dimensions111
13 Technical Details Order No. 6D000034115
14 Technical Details Order No. 6D000020-6D000021118
15 Safety Characteristic Data121
16 Network Data122
17 Order Reference123
- System123
- Accessories123
18 Appendix126
- Check List126
19 Identification129
20 EC Declaration of Conformity130

Related product manuals

Preview: Pilz PSEN sc M 3 Series

Pilz PSEN sc M 3 Series

Pilz PSEN sc M 3.0 08-17

Preview: Pilz PSEN sl-1.0p 1.1

Pilz PSEN sl-1.0p 1.1

Preview: Pilz PSEN cs1.1p

Pilz PSEN cs1.1p