Need help?Do you have a question about the Pioneer DEH-P825R and is the answer not in the manual?
General| Detachable Face | Yes |
|---|---|
| CD-R/CD-RW Compatible | Yes |
| Preamp Outputs | 3 Pairs |
| Subwoofer Preamp Output | Yes |
| USB Input | No |
| Channels | 4 |
| Built-in Crossover | Yes |
| Remote Control | Yes |
| Tuner Bands | FM/AM |
| Preamp Output Voltage | 4 Volts |
Provides details about the tuner/CD player's features, compliance, and operational areas.
Explains the purpose and recommendations for reading the operation manual for full benefit.
Instructions on how to reset the microprocessor under specific conditions like first-time use or malfunction.
Explains how to temporarily stop and restart CD playback using button 8.
Details the available repeat modes: Disc Repeat (normal play) and One-track Repeat.
Describes how to activate and cancel Random Play mode for variety in track playback.
Explains how to activate and cancel Scan Play, which plays the first 10 seconds of each track.
Information on entering disc titles for up to 100 discs via the ADPS function for easier selection.
Instructions for operating multi-CD players, including source selection and display information.
How to select and switch between connected multi-CD players using the Band button.
Methods for selecting a disc using the Disc Number Search function via remote or main unit.
Details the four repeat modes available: One-track, Disc, Multi-CD player, and All Repeat.
Explains how to activate and cancel Random Play for multi-CD players across different repeat modes.
Describes how to activate and cancel Scan Play for multi-CD players in various modes.
Function allowing track search when multi-CD players are installed, utilizing ADPS for title input.
Instructions on how to program desired tracks for automatic playback using the ITS function.
How to perform playback of ITS programmed tracks in any repeat mode.
Details the ITS playback options and behavior for multi-CD players in different modes.
Procedures for erasing ITS track or disc programs, stored permanently until erased.
Steps to erase a specific programmed track during ITS playback.
Steps to erase an entire programmed disc during ITS playback.
Instructions for entering disc titles up to 100 discs via ADPS for simplified search and selection.
Instructions for playing a disc by its entered title in a multi-CD player.
Adjusting sound quality using COMP (compression) and DBE (dynamic bass emphasis) functions.
How to switch between COMP and DBE functions and their respective levels.
Table listing common error messages, their possible causes, and recommended corrective actions.
How to select and apply different sound field settings (STUDIO, CLUB, JAZZ CLUB) for optimal listening.
Two methods are described for selecting the Sound Field Control (SFC) setting.
Procedure to exit the Sound Field Control (SFC) mode using the DSP button.
Details on using the digital equalizer with factory preset or user-defined curves and controls.
How to apply equalizer effects selectively to front, rear, or both speakers.
Methods for selecting equalizer curves, including factory presets and user-stored curves.
Fine adjustment of equalizer curves using NCE or 13-Band G.EQ, with options for storage.
Steps for fine-tuning equalizer curves using the Nuance Control Equalizer (NCE).
Adjusting sound via a 13-band graphic equalizer for front and rear speakers separately.
How to store adjusted equalizer curves under user buttons (1-4) for quick recall.
Procedure to exit the Digital Equalizer mode using the DSP button.
Setting the listening position to match passenger seating for optimal sound stage and balance.
Adjusting the digital attenuator to prevent crackling sound (L) or optimize S/N (H).
Describes the three available modes: Music, Blank, and Program for background sound effects.
The same track is played repeatedly on the built-in CD player during main source playback.
Allows a sub-source sound effect to fade in between tracks or during pauses on the main source.
Permits programming a different sub-source sound effect for every track played on the main source.
Steps to activate and use the SOUND SCAPE function with tuner, AUX, or multi-CD player as main source.
Procedures for adjusting the sub-source volume for the selected SOUND SCAPE effect.
How to enter the setting mode and adjust the volume for the sub-source sound effect.
How to change SOUND SCAPE modes (MUSIC, BLANK, PGM) when using a multi-CD player.
How to stop the SOUND SCAPE playback and continue main source playback.
How to select a specific sub-source track for playback in MUSIC or Blank modes.
How to program sound effects for tracks on up to 24 discs in PROGRAM mode with multi-CD players.
Basic specifications including power source, grounding, consumption, dimensions, and weight.
Technical specifications for the amplifier, including power output, impedance, and loudness contour.
Details on equalizer controls, frequency ranges, equalization range, and subwoofer output crossover.
Specifications related to the CD player system, usable discs, signal format, and frequency characteristics.
Technical specifications for the FM tuner, including frequency range, sensitivity, and signal-to-noise ratio.
Technical specifications for the MW tuner, including frequency range, usable sensitivity, and selectivity.
Technical specifications for the LW tuner, including frequency range, usable sensitivity, and selectivity.
To Next Page
