Need help?Do you have a question about the Posligne ODP 200 and is the answer not in the manual?
General| Print Resolution | 203 dpi |
|---|---|
| Power Supply | 24 VDC |
| Print Technology | Direct Thermal |
| Connectivity | USB, Serial |
| Supported Barcode Types | UPC-A, UPC-E, EAN8, EAN13, Code39, Code128, ITF, Codabar |
Details about printing method, dot density, direction, width, characters per line, printing speed, and line spacing.
Information on character count, structure, size, printing direction, paper width, and character/line count for different emulations.
Details on partial cut functionality and paper feed requirement after cutting.
Describes supply method, near-end sensor detection, paper roll spool diameter, and remaining amount.
Details on paper type, form, width, roll size, and spool diameter requirements.
Diagrams showing printable area for EPSON and STAR emulations in different paper width models.
Diagram illustrating manual cutter, auto-cutter blade, and print dotline positions with dimensions.
Details supply voltage and current consumption for operating, peak, and stand-by modes.
Lists EMI and safety standards applied for Europe and North America.
Provides MCBF (Mean Cycles Between Failures) and Cutter Life specifications.
Specifies operating and storage temperature and humidity ranges.
Introduces interface configuration options.
Details RS-232 serial interface specifications, handshaking, signal levels, baud rate, etc.
Lists serial interface data transmission, synchronization, handshaking, signal levels, baud rate, etc.
Explains how the printer switches between on-line and off-line states.
Table listing PIN, SIGNAL, I/O, and DESCRIPTION for interface connectors.
Provides wiring diagrams and timing examples for serial interface connections.
Details pin assignments, signals, I/O, and descriptions for Centronics parallel interface.
Table specifying timing characteristics for data receiving in compatibility mode.
Details USB interface specifications, pin assignments, and connection examples.
Lists pin assignments for Ethernet interface.
Diagrams showing various interface connectors like D-SUB, Centronics, USB, Ethernet.
Repeats input voltage and current consumption details.
Details the drawer kick-out connector, pin assignments, and connector model.
Explains the notation used for commands (Name, Format, Range, Description, etc.).
Introduces the section detailing control commands.
Sets horizontal tab position.
Prints data and feeds one line.
Prints and returns carriage.
Prints in page mode and returns to standard mode.
Cancels print data in page mode.
Real-time status transmission.
Real-time request to printer.
Generate pulse at real-time.
Prints all buffered data in page mode.
Sets right-side character spacing.
Selects print mode(s) (font, emphasized, double-height, etc.).
Sets absolute print position.
Selects or cancels user-defined character set.
Defines user-defined characters.
Selects bit-image mode.
Turns underline mode on/off.
Selects default line spacing.
Sets line spacing.
Selects peripheral device.
Cancels user-defined characters.
Initializes printer.
Sets horizontal tab positions.
Turns emphasized mode on/off.
Turns double-strike mode on/off.
Prints and feeds paper using minimum units.
Selects page mode.
Selects character font.
Selects an international character set.
Selects standard mode.
Select print direction in page mode.
Turns 90° clockwise rotation mode on/off.
Sets printing area in page mode.
Sets relative print position in page mode.
Selects justification (left, center, right).
Selects paper sensor(s) to output paper-end signals.
Selects paper sensor(s) to stop printing.
Enables/disables panel buttons.
Prints and feeds n lines.
Generates pulse to connector pin.
Selects character code table.
Turns upside-down printing mode on/off.
Prints NV bit image.
Defines NV bit image.
Selects character size.
Sets absolute vertical print position in page mode.
Defines downloaded bit image.
Prints downloaded bit image.
Turns white/black reverse printing mode on/off.
Selects printing position of HRI characters.
Transmits printer ID.
Sets left margin.
Sets horizontal and vertical motion units.
Selects cut mode.
Sets printing area width.
Sets relative vertical print position in page mode.
Enables/Disables Automatic Status Back (ASB).
Selects font for HRI characters.
Selects barcode height.
Prints bar code.
Transmits status (paper sensor, drawer kick-out).
Prints raster bit image.
Sets bar code width.
Performs a full paper cut.
Performs a partial paper cut.
Sets print mode(s) for Kanji characters.
Selects Kanji character mode.
Turns underline mode on/off for Kanji characters.
Cancels Kanji character mode.
Defines user-defined Kanji characters.
Selects Kanji character code system.
Sets left- and right-side Kanji character spacing.
Turns quadruple-size mode on/off for Kanji characters.
To Next Page
