EasyManua.ls Logo

Preiffer HiPace 3400 MC User Manual

Preiffer HiPace 3400 MC
34 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Translation of the original instructions
Operating Instructions
EN
PT 0191 BEN/E (1208)
HiPace 3400 MC
Turbopump

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Preiffer HiPace 3400 MC and is the answer not in the manual?

Preiffer HiPace 3400 MC Specifications

General IconGeneral
BrandPreiffer
ModelHiPace 3400 MC
CategoryWater Pump
LanguageEnglish

Summary

Safety Instructions

For Your Orientation

Provides guidance on understanding symbols and actions indicated in the manual.

Pictograph Definitions

Explains the meaning of standard symbols used throughout the document for warnings and cautions.

Understanding The HiPace 3400 MC Pump

Main Features

Outlines the key components and characteristics of the HiPace 3400 MC turbopump and its controller.

Proper Use

Details the intended applications and conditions for the HiPace 3400 MC turbopump.

Improper Use

Lists prohibited or unsafe operating conditions and actions for the turbopump.

Scope Of Delivery

Specifies the components included with the HiPace 3400 MC turbopump upon purchase.

Installation

Preparations For Installation

Covers essential preliminary steps and safety precautions before installing the turbopump.

Connecting The High Vacuum Side

Guides on how to properly connect the turbopump to the high vacuum system.

Earthquake Safety

Explains measures to secure the turbopump against seismic events and related forces.

Installing The High Vacuum Flange

Details the procedure and requirements for attaching the turbopump's high vacuum flange.

Connecting The Fore-Vacuum Side

Provides instructions for connecting the turbopump to the fore-vacuum system.

Connecting The Cooling

Outlines the necessary steps and requirements for connecting the turbopump's cooling system.

Electronic Drive Unit And Magnetic Bearing Controller TM 3000

Describes the TM 3000 unit and its connection to the power supply for turbopump operation.

Connecting The Venting Valve and Sealing Gas Valve

Explains the connection of integrated venting and sealing gas valves on the turbopump.

Connecting The Remote Control

Details how to connect external control units or systems to the turbopump's remote interface.

Connecting The Serial Interface. Using A DCU Or HPU

Guides on establishing serial communication with the turbopump via DCU, HPU, or PC.

Connection Diagram

Presents a visual representation of the turbopump's electrical and signal connections.

Operations

General Operating Information

Provides essential background and safety considerations for operating the turbopump.

Operating Modes

Explains the different ways the turbopump can be controlled and operated.

Before Switching ON

Lists critical checks and precautions to be taken before powering on the turbopump.

Switching ON

Describes the procedure for starting up the turbopump and initial checks.

Normal Operation Of The Turbopump

Details the standard operating procedures and performance characteristics of the turbopump.

Standby Rotation Speed ON/OFF

Explains how to activate and configure standby rotation speed for the turbopump.

Turbo Drive ON/OFF

Describes the control for turning the turbopump's drive motor on and off.

Rotation Speed Switch Point

Explains the function and parameters related to the turbopump's rotation speed switch point.

Rotation Speed Set Mode

Details how to set and operate the turbopump at specific rotation speeds.

Backing Pump Operation

Describes how to control and monitor the operation of the backing pump.

Gas Type Dependent Operation

Explains how gas type affects pump performance and power characteristics.

Switching Off And Venting

Provides instructions for safely shutting down and venting the turbopump.

Emergency Stop

Details the procedure for initiating an emergency stop for the turbopump.

Safety Bearings

Explains the function and monitoring of the turbopump's safety bearings.

Monitoring Of The Balancing Condition

Describes how to monitor the rotor's balancing condition and potential warnings.

Emergency Power Operation

Outlines the turbopump's behavior during power failures and emergency power situations.

Shut Down For Longer Periods

Provides guidelines for safely storing the turbopump for extended periods.

Remote Control Operation

Explains how to control the turbopump remotely using various interface options.

Venting Modes

Details the different modes available for venting the turbopump.

Configuration Of The Analog Output

Guides on setting up the analog output for monitoring turbopump parameters.

Switching Outputs

Explains the configuration and function of the turbopump's switching outputs.

Configuration Of The Maximum Drive Power

Describes how to limit the maximum drive power based on the power supply.

Error Messages And Warnings

Error Messages / Status Messages

Lists and explains the various error codes and their troubleshooting steps.

Warnings

Lists and explains warning codes and their potential functional restrictions.

Parameters

General

Introduces the parameter system for the TM 3000 controller and parameter types.

Setting Commands

Details the parameters that can be adjusted and their functions.

Status Requests

Lists status parameters that can be read from the TM 3000 controller.

Set Points

Details the set point parameters that can be configured for the turbopump.

Monitoring The Operating Conditions

Operating Mode Display Via LED

Explains how to interpret the operating status displayed by the LEDs on the TM 3000.

Temperature Monitoring Of The Turbopump

Describes how temperature affects turbopump performance and potential shutdowns.

What To Do In Case Of Breakdowns?

Service

Maintenance

Technical Data

Dimensions

Provides dimensional drawings and measurements for the turbopump.

Accessories

Declaration of conformity