PREVOST LE MIRAGE XLII BUS SHELLS User Manual

Section 26: XLII SLIDE-OUT
PA1553
3
19 SLIDE-OUT MAXIMUM LOAD..............................................................................................................39
20 CONVERSION CHECKLIST .................................................................................................................40
20.1 ERROR CONDITION OR MISSING OPERATION CONDITION...................................................................41
20.2 TROUBLESHOOTING – OPERATING CONDITIONS & CONTROL .............................................................41
20.3 TROUBLESHOOTING - MECHANICAL COMPONENTS ............................................................................43
20.4 SLIDE-OUT FAULT MESSAGE ON MESSAGE CENTER DISPLAY (MCD).................................................46
LIST OF ILLUSTRATIONS
FIGURE 1 : FRONT SLIDE-OUT..................................................................................................................5
FIGURE 2 : REAR SLIDE-OUT ....................................................................................................................5
FIGURE 3 : SIDE INNER STOPPER ADJUSTMENT ..................................................................................5
FIGURE 4: UPPER INNER STOPPERS ADJUSTMENT..............................................................................5
FIGURE 5: LOWER "IN LIMIT" STOPPER...................................................................................................6
FIGURE 6: UPPER "IN LIMIT" STOPPER ....................................................................................................6
FIGURE 7 : EXTERIOR EXTRUSION..........................................................................................................6
FIGURE 8: SECURITY PIN AIR CYLINDER REMOVAL ..............................................................................7
FIGURE 9 : FRONT SLIDE-OUT ROOF REINFORCING ROD...................................................................7
FIGURE 10 : RACK.......................................................................................................................................8
FIGURE 11: PINION AND KEYLESS BUSHING POSITIONING..................................................................9
FIGURE 12: PINION AND KEYLESS BUSHING AS SEEN FROM EVAPORATOR COMPARTMENT........9
FIGURE 13: MECHANICAL COMPONENTS (TYPICAL) .............................................................................9
FIGURE 14 : KEYLESS BUSHING TIGHTENING .....................................................................................10
FIGURE 15 : TORQUE WRENCH FORMULA...........................................................................................10
FIGURE 16 : KEYLESS BUSHING INSTALLATION INSTRUCTION .........................................................12
FIGURE 17: ELECTRIC MOTOR AND SPEED REDUCTION GEARBOX .................................................13
FIGURE 18: DRIVE MOTOR/GEARBOX ASSEMBLY MOUNTING BOLTS ..............................................13
FIGURE 19: CLAMPING HUB POSITION ON GEARBOX SHAFT.............................................................14
FIGURE 20: JAW COUPLING.....................................................................................................................14
FIGURE 21: SLIDE-OUT LEVEL ADJUSTEMENT.....................................................................................15
FIGURE 22 : SLIDE-OUT LEVELING.........................................................................................................16
FIGURE 23: TILT ADJUSTMENT ...............................................................................................................16
FIGURE 24 : RAIL POSITIONING...............................................................................................................17
FIGURE 25: ACETAL PLASTIC BLOCKS...................................................................................................17
FIGURE 26: REMOVE THE UPPER ACETAL PLASTIC BLOCKS WITH A PICKING TOOL.....................17
FIGURE 27: LOWER ACETAL PLASTIC BLOCK INSERTION ..................................................................18
FIGURE 28 : FRONT SERVICE COMPARTMENT....................................................................................19
FIGURE 29: PNEUMATIC COMPONENT PANEL......................................................................................20
FIGURE 30 : SEAL ASSEMBLY.................................................................................................................20
FIGURE 31: REAR SLIDE-OUT INFLATABLE SEAL AIR INLET ...............................................................21
FIGURE 32: SLIDE-OUT 2" INSIDE – UPPER PART .................................................................................22
FIGURE 33 : DASHBOARD SLIDE-OUT TELLTALE LIGHT.....................................................................23
FIGURE 34: MAIN BREAKER IN ENGINE R.H. SIDE ACCESS COMPARTMENT....................................23
FIGURE 35 : SLIDE-OUT CONTROL PANEL............................................................................................23
FIGURE 36 : VEC CIRCUIT BREAKERS & FUSES ..................................................................................24
FIGURE 37 : FRONT SLIDE-OUT SENSORS ...........................................................................................25
FIGURE 38: REAR SLIDE-OUT SENSORS ...............................................................................................25
FIGURE 39 : MAGNETS ON SLIDE-OUT UNDERBODY..........................................................................25
FIGURE 40 : SLIDE-OUT PANELS AND WINDOWS................................................................................26
FIGURE 41 : SIDE PANEL INSTALLATION – DOUBLE FACE ADHESIVE TAPE APPLICATION ON THE
SLIDE-OUT STRUCTURE...................................................................................................................27
FIGURE 42 : SIDE PANEL INSTALLATION – SIKA 206 G+P APPLICATION..........................................27
FIGURE 43 : SIDE PANEL INSTALLATION – SIKA TACK+BOOSTER APPLICATION..........................27
FIGURE 44 : SIDE PANEL INSTALLATION ...............................................................................................28

PREVOST LE MIRAGE XLII BUS SHELLS Specifications

General

Brand	PREVOST
Model	LE MIRAGE XLII BUS SHELLS
Category	Buses
Language	English