Propert Omega - Page 2

OPERATING INSTRUCTIONS
It is advisable to read through the Instructions first before
attempting to operate the scale. Bypassing certain
procedures may give incorrect readings.
PREPARING YOUR SCALE
1. Before attempting to use your Propert Glass Body Analysis
scale, remove all packaging.
2. Then open the battery compartment cover on the base of
the scale & insert the 2 Lithium batteries (CR2032)
provided. Ensure the batteries are placed inside the
compartment with the positive (+) sides facing up.
Replace the compartment cover.
3. Ensure you remove shoes, socks or stockings before using
the scale as this may affect body fat and water content
readings
Power on for a body Scroll up, Scroll down,
analysis reading, change unit change unit
menu select, confirm measure measure
OPERATING MODES
The Propert Glass Body Analysis Scale has 2 operating
modes for -
e Weighing only and...
e Weighing to compute your body fat, water, muscle, bone
percentage and BMI
(“Personal data must be set for this function. This scale is able to store
data including gender, height and age for 10 people).
Weighing Only
1. Place the Scale on a hard & even surface. Use on carpet
or uneven surfaces may cause inaccuracies.
2. To turn the scale on for weighing only, tap on the scale
platform with your foot.
3. The scale briefly displays ‘8888’ before it nm s
‘zeroes Indicating it is in weighing mode Uu
and ready for use.
4, At this point, select the unit measure (kilograms, @)
stones pounds or pounds) by pressing the
conversion button underneath the scale
5. Then gently step onto the scale. When standing on your
scale, make sure your feet are placed evenly, your
weight is distributed evenly between your feet and you
stand perfectly still. Movement, leaning backward or
forward or not standing evenly on your scale, will affect
the accuracy of the weight displayed.
6. Your weight value will be shown on the display
7. If left idle, the scale automatically turns off
Entering personal data
(the digits PO - P9 represent each of 10 users).
1. Turn the scale on by pressing the ‘SET’ button
2. A personal user number at the bottom left corner of the
screen flashes.
3. Press either of the arrow buttons to select a number of your
choice.
4, The digits PO - P9 represent each of 10 users. Remember
this number for future reference. You might want ‘PO’ for
yourself, your partner might like ‘P1’, your son ‘P2’,
daughter ‘P3’ and so forth. Press the ‘SET’ button to ‘lock’ it in
5. A gender symbol flashes. Press either of the arrow buttons to
make your selection, then press the ‘SET’ button to ‘lock’ it in.
T
6. The number for years flash. Press either of the arrow
buttons to scroll up or down to enter your age, then press
the ‘SET’ button to ‘lock’ it in
7. Height measurements then flash. Press either of the arrow
buttons to scroll up or down to enter your height, then press
the ‘SET’ button to ‘lock’ it in. (If ‘Kg’ was chosen as
the medsurement unit, then your height will be shown in
terms of ‘cm’. If ‘stone pounds’ or just ‘bounds’ were chosen,
then height would display in feet and inches).
8. The programming of personal data is now completed.
The scale shows 4 dotted lines, then ‘zeroes’, indicating it
is ready for use. You may step on it for a body analysis
reading...Or
9. You may continue to enter data for another user or
modify data by repeating Steps 1-7. Remember that
each other person will have a different identifying user
number.
Toggle between:-
Male symbol located on the left above
the personal number.
Female symbol located on the right
above the personal number.
Weighing to compute your body fat, water, muscle, bone
percentage and BMI
1. Tap the scale to turn it on
2. Press either of the arrow buttons to find the number you
chose as your personal user number. There is no need to
press ‘Set’ once you have located the number.
Wait until the scale shows ‘zero’ indicating it is ready for use.
4, Gently step onto the scale. > >
“Note that your bare feet must
be centred over and on the
electrodes (vertical metal strips) |
for an effective reading. l
=
“These electrodes allow a very low electrical
impulse (which cannot be felt) to pass
through the body. The scale applies
Bioelectrical Impedance Analysis (BIA) to
compute the measurements.
Your weight is then shown.
5. Continue to stand still. The scale
will flash 4 x ‘0’ while computation h oO oO
is taking place. Pa
6. Your body fat, water, muscle, bone percentages and
BMI will appear on the screen and display 2 times
sequentially
co ? Ig"
to I oo
JTI a” "a ” —
A l f LI fat = A a da > h = 3
7. The scale automatically turns off after that.
LAST RESULT RECALL FUNCTION
After measuring weight, fat, water, muscle, bone and BMI,
the scale automatically stores the data into memory
l. To view these results, turn the scale on and select your
personal user number (No need to press ‘SET’ after
that). The scale will display your last recorded
measurements.
2. The scale then ‘zeroes’ ready for use again.
3. When you measure yourself again, the scale will
record the new results and this will replace the old
data
OVERLOADING
If the scale is overloaded (over 150kg / 23st / 330lb), ‘EEEE’
appears on the display. Remove the weight immediately
or damage to the scale may occur.
LOW BATTERY INDICATOR
When ‘LO’ displays on the screen, the batteries must be
replaced. Remember, always use fresh, good quality
lithium batteries.
ERROR INDICATION
‘Err2’ indicates that body analysis has been unsuccessful,
or quite often, that body fat content is less than 5% or more
than 50%
SPECIFICATIONS
6mm thick tempered glass platform
Capacity - 150kg / 23st / 330lb
Weight graduation - 0.1kg / 1/4lb / 0.2lb
Body Fat percentage range 5 - 50%; Graduation 0.1%
Water percentage range 20 - 70%; Graduation 0.1%
Muscle range 15 - 75%; Graduation 0.1%
Bone weight range 1 - 11.7Kg / 2.2 - 25.8lb
Age range 10 - 80 years
Height range 100 - 225cm / 3'3"- 7'3":
Graduation lcm / 1"
Battery - 2 x CR2032 batteries (included)