SPECS
Size: 1.5 x 3 x 5.5 in (38.2 x 76.6 x 139.4 mm)
Maximum Cartridge Size: 11.5 mm diameter/61 mm length
Battery Capacity: 650 mAh
Voltage: 2.8 V / 3.4 V / 3.8 V
Charging: USB-C
Resistance: 0.8-2.0 Ω
Static Current: ≤10uA
POWERING ON/OFF
To turn the device on or off, press the button 5 times. The indicator light will remain on for one second to indicate
the power-on or power-off state. The device does not have auto-shutoff and must be turned off manually.
PRE-HEATING
Press the button 2 times within 15 seconds or inhale 2 times quickly to pre-heat the device. Colorful rainbow lights
and a fire icon will flash to indicate that it is pre-heating. The process will be interrupted if you do anything else with
the device while it’s pre-heating.
SCREEN DISPLAY
The screen displays the current voltage level, the battery level, and a lightning icon during charging. The screen
turns off after 10 seconds of inactivity.
ADJUST VOLTAGE
Press the button 3 times within 1.5 seconds or inhale 3 times quickly to adjust the voltage. The corresponding light
color for each voltage will flash 3 times when selected.
2.8 V - Green (L) 3.4 V - Blue (M) 4.0 V - Red (H)
The voltage and battery percentage levels are always on the display screen while the voltage is being adjusted. The
current voltage will flash 3 times and then stay on for 10 seconds.
BATTERY LEVEL INDICATOR
Short press the button to display the current battery level when in normal working mode.
When over 75%, the green light will turn on for 2 seconds.
When between 35-75%, the blue light will turn on for 2 seconds.
When below 35%, the red light will turn on for 2 seconds.
When voltage drops below 3.2 V, the red light will flash 10 times, indicating that the device has entered the standby
state. On the screen display, the voltage level will be shown as 0. The device does not support pass-through use or
fast charging.
INSTRUCTIONS
1. Charge the battery using the provided USB-C cable. Plug into the connector on the bottom of the unit and
attach the cable to a power source. The red light will turn on when it is connected and charging.
2. Allow the battery to fully charge before use. The light will turn green when the device is fully charged. Discon-
nect the device from the cable when it is fully charged.
3. Remove the pipe stem (twist off) and screw in a 510 threaded cartridge of your choice into the bowl of the pipe.
4. Reattach the pipe stem (twist on and lock) and ensure it is firmly connected before use. Use without the stem
for larger cartridges.
5. If the unit is turned off, press the button five times to turn it on.
6. Adjust the voltage by pressing the button 3 times or inhaling on the mouthpiece 3 times. (Green Light = 2.8 V,
Blue Light = 3.4 V, Red Light = 4.0 V)
7. Pre-heat the device by pressing the button 2 times or inhaling on the mouthpiece 2 times. Colorful rainbow
lights will flash to indicate that it is pre-heating.
8. Press and hold the button or inhale slowly to vape. The current voltage light will brighten and remain on while
vaping. The light will gradually fade out when you stop. While vaping, the screen displays the voltage setting
and static current light.
PU-0781-24
PulsarShop.com
INSTRUCTION
MANUAL
CHANGING DISPLAY
A full charge of the 510 DL Pipe takes about 70 minutes.
When charging, the red light will stay on. Once the device is
fully charged, the green light will stay on. During charging,
the screen shows the battery percentage, and the lightning
icon will continuously flash. When the 510 DL Pipe is fully
charged, the screen will display 100% battery level, and the
lightning icon will stay on.
When the charge cable is disconnected, the lightning icon
will disappear, and the battery level and current voltage will
display.
PROTECTION FEATURES
Battery Protection (Vaping Timeout): If vaping exceeds 10
seconds, the red light will flash four times, indicating that
the device has entered the standby state. The battery level
and current voltage will continue to be displayed on screen
as normal.
Over-Voltage & Overload Protection: if an overly high
voltage is detected, the 510 DL Pipe will enter a protection
state and turn off. During this state, the indicator light
remains off. If the device is connected to the charge cable,
the screen display will continuously flash "00". The screen
will return to normal when the charging plug is removed.
WARNINGS
Do not expose to extreme temperatures or direct sunlight. Do not drop the device or accessories. Do not drop or
submerge in any liquid. Do not modify the electronics in any way. This device is intended for adults only. Do not
sell or provide to minors. Keep all parts, concentrates, herbs, and liquids away from children and pets. This is not
a medical device and is not intended to diagnose, treat, mitigate, cure, or prevent any ailment, disease, or other
conditions. Consult a physician before use, especially if you suffer from heart disease or any other medical
condition, or if you are pregnant or breastfeeding. Failure to follow any of these instructions could result in
product damage, property damage, personal injury, and may void warranty. Visit PulsarShop.com for warranty
information.
To Next Page
Loading...