Using The Weaver Rail
25
The riflescope is equipped with a Weaver rail (13) which allows the user to mount
extra accessories such as:
џ LED IR Illuminators Pulsar-805/Pulsar-940/Pulsar- X850 (#79071/79076/79074)
џ IR Illuminator Pulsar AL915 (#79132)
Technical Inspection
26
Please check before every hunt:
џ External view (there should be no cracks on the housing).
џ Correct mounting of the riflescope on your rifle (clearances are not allowed).
џ Correct functioning of the controls.
џ Ensure that the objective lens, eyepiece, IR illuminator are free of cracks, grease
spots, dirt, water stains and other residue.
џ Smoothness of the objective lens focus knob, dioptre focus knob.
џ The state of the Battery Pack (should be charged) and electric terminals (there
should be no oxidation).
Technical Maintenance
27
Technical maintenance should be done at least twice a year, includes the following
steps:
џ Clean the outside metal and plastic surfaces from dust, dirt and moisture; wipe
the scope with a soft lint free cloth.
џ Inspect the eyepiece lens, the objective lens, IR illuminator and rangefinder and
gently blow off any dust and sand, and clean using lens cleaner and a soft cloth.
џ Inspect the eyepiece lens, the objective lens, IR illuminator and gently blow off
any dust and sand, and clean using lens cleaner and a soft cloth.
Storage
28
џ Always store the riflescope in its carrying case in a dry, well-ventilated space.
џ For prolonged storage, remove the Battery Pack.
Troubleshooting
29
Listed below are some potential problems that may occur when using the scope.
Carry out the recommended checks and troubleshooting steps in the order listed.
Please note that the table does not list all of the possible problems. If the problem
experienced with the scope is not listed, or if the suggested action meant to
correct it does not resolve the problem, please contact your seller.
PROBLEM
The riflescope will not turn on.
The riflescope will not operate
on external power supply.
The reticle is blurred and
cannot be focused with the
dioptre knob.
The image is too dark.
With a crisp image of the
reticle, the image of the
observed target that is at least
30 m away is blurred.
The aiming point shifts after
firing rounds.
The riflescope will not focus.
Smartphone or tablet PC
cannot be connected to the
riflescope.
POSSIBLE CAUSE
The Battery Pack is empty.
USB cable is damaged.
External power supply is
discharged.
The diopter adjustment range
is not enough for your
eyesight.
Condensation on the external
surface of the eyepiece lens.
Brightness or contrast level
is too low.
Dust and condensate are
covering the outside optical
surfaces after the riflescope
was brought in from the cold
into a warm environment, for
example.
The riflescope is not mounted
securely or the mount was not
fixed with thread sealant.
Wrong settings.
The riflescope is used in the
daytime at long distances.
Password in the riflescope was
changed.
СORRECTIVE ACTION
Charge the Battery Pack.
Replace USB cable.
Charge the external power
supply (if necessary).
If you wear prescription
glasses with a range of +/-5,
keep glasses on when looking
through the eyepiece.
Clean the lens with a cloth.
Adjust brightness/contrast
level.
Clean the lens surfaces with a
blower and soft lens cloth.
Let the riflescope dry by
leaving it in a warm
environment for 4 hours.
Check that the riflescope has
been securely mounted, make
sure that the same type and
calibre bullets are being used
as when the scope was initially
zeroed; if your riflescope was
zeroed during the summer, and
is now being used in the
winter (or the other way
round), a slight shift of the
aiming point is possible.
Adjust the riflescope according
to the instructions given in the
Section 9 “OPERATION” and
check the surfaces of the
eyepiece and objective lenses
and clean them if necessary
from dust, condensation, frost,
etc; to prevent fogging in cold
weather, apply a special anti-
fog solution.
Check focusing in the
nighttime.
Delete network and connect
again inserting the password
saved in the riflescope.
To Next Page
Loading...