Deactivate "Automatic Lock Out"by
pressing the MODE/LOCK button
until the lock icon ( ) disappears
Bearing Shaft Diameter Dispensing Period Lube Cycle Dispensing Volume LCD Display
166mm(6.5") ~ 229mm(9.0")
102mm(4.0") ~ 165mm(6.5")
90mm(3.5") ~ 101mm(4.0")
77mm(3.0") ~ 89mm(3.5")
65mm(2.5") ~ 76mm(3.0")
51mm(2.0") ~ 64mm(2.5")
25mm(1.0") ~ 50mm(2.0")
Less than 25mm(1.0")
16.6ml/day
33.3ml/dayH (Half) 15 min
30 min
1 hr
2 hr
3 hr
6 hr
9 hr
12 hr
1month
2month
4month
6month
12month
24month
18month 0.9ml/day
0.7ml/day
8.3ml/day
4.2ml/day
2.8ml/day
1.4ml/day
Available Mounting Options
Direct Straight Mount (with or without extension tube) is always
preferable. However, for applications not allowing any direct mounts
or extension mounts, remotely mount the unit using 6mm OD (1/4")
pre-filled lube line.
WARNING
Single Point Lubrication Multi Point Lubrication Using Progressive Divider Block
Remote multi point lubrication is available with the Pulsarlube M500 using a divider
block. It is recommended to test the back pressure of the bearing, lube lines, and
divider block after assembly using a grease gun connected to a pressure gauge.
Ensure the break-off pressure is below the average operating pressure of 30kgf/cm²
(425psi).
Automatic Grease Lubricator for Larger Bearings
PULSARLUBE M500, 500ml Grease Lubricator
Models
Specifications
500ml (replaceable)
30~60kgf/cm² (425~850psi)
3/8" Male BSPT
Up to 8 points
Half (H), 1, 2, 4, 6, 12, 18 & 24 months
Ø92mm (3.6") × 260mm (10.2")
1.30kg (2.86 lbs) for fully assembled unit
Up to 6m (20ft) using a 6mm (1/4") O.D.
pre-filled lube line
Description
Product Details
How to Order
Technical information is subject to change without notice.
Before Use
Shelf Life and Product Warranty
M500 / PL1
M500 / PL5
Pulsarlube Model #
Grease Type
/
500
Thank you for purchasing the Pulsarlube M500. The Pulsarlube M500 is primarily designed to meet the requirements of larger
bearings, To ensure the safe operation and proper installation of the Pulsarlube M500 unit, we strongly recommend that you
read the following information carefully before use.
If you require further information, please contact your local supplier or manufacturer.
-15˚C ~ 60˚C (5˚F ~ 140˚F)
-40˚C ~ 60˚C (-40˚F ~ 140˚F) *
* with optional Lithium Battery Pack
The dispensing period setting
The # of days remaining until the
end of lube cycle
The unit is in"Automatic Lock Out"
mode
Grease pouch capacity
The test mode is activated
Select the dispensing rate in
ascending order: 1▶2 ▶ 4 ▶ 6 ▶
12 ▶ 18 ▶ 24 ▶Half (H)
Test function prior to installation or
after changing the service pack
The # of days after dispensing
has completed
The # of days on stand-by mode
due to excessive backpressure
Low battery power
Excessive backpressure exists
Empty grease level
OIL
Buttons
LCD Display - Function
M500
Housing
Pouch
Spring
Pouch
Plate
Grease
Pouch
Buttons
Connecting Thread
3/8"BSPT
LCD
Main Body
Lube Cycle & Dispensing Recommendations
Signal lamp blinks periodically
when battery power is low, excessive
backpressure exists, or if grease
level is empty
Press the POWER button for 2
seconds to turn unit on or off.
Reset the unit when the unit
malfunctions and/or after changing
the service pack
Keep the maximum distance per lube point at 6m (20ft) or less.
Grease Pouch
Installation Thread Size
Available Dispensing Periods
Multi Point
Weight
Product Size
Remote Installation
Operating Pressure
Operating Temperature
Specifications
The shelf life of each Pulsarlube M500 unit is 1 year from the date of
production. Product warranty is limited to original defects in material
and workmanship and will not cover any collateral damage due to
mishandling, abuse and /or any other inappropriate use of this
product. Warranty period is 1 year from the date of purchase.
USER MANUAL
Pulsarlube USA, Inc.
1480 Howard Street, Elk Grove Village, IL 60007, USA
www.pulsarlube.com / info@pulsarlube.com
Doc No. 1042-000 REV. 140203
TEL: 1-847-593-5300 FAX: 1-847-593-5303
To Next Page
Need help?
General
