7.1 Regatta Timer Mode - Setting the User Preset Value
How to Set the User Preset Value
+ To select setting display, hold the [M] button
for 2 seconds, and the flashing "SET" icon
will appear.
+ In setting display, press the [M] button to
change the selection among hour, minute and
second following the adjacent diagram.
+ When the digits are flashing (selected), press
the [ S /S] or [ L /R] butt o n to i n crease /
decrease the number. (Hold down the button
to change the number at a higher speed).
+ When the setting is completed, hold down the
[M] button to exit the setting display. The
Watch will also exit the setting display if NO
keystroke has been activated for 1 minute
Increase/ decrease
the number
Increase/decrease
the number at
a higher speed
hold [S/S] / hold [L/R][S/S] / [L/R]
User Preset Value Setting Sequence
Regatta Timer Display
hold
[M]
Setting Display
minute
Second
hour
hold
[M]
[M]
[M]
[M]
digits
selected
(flashing)
7.2 Regatta Timer Mode - Using the Regatta Timer
How to Use the Regatta Timer
+ When a target time is set by using the Quick
Set Value or User preset Value, press the [S/S]
button to start the counting. When the timer is
counting, press the [S/S] button once again to
stop the counting.
+ Once the timer is started, the countdown time
will show on the display continuously, and the
Watch w ill al ert th e user by beeping as
follows:
+ The last 10 minutes: The watch will beep
once for every minute.
+ The last one minute: The watch will beep
for every 10 seconds.
+ The last 10 seconds: The watch will beep
for every second(s).
+ A t z e r o : t h e W a t c h w i l l s w i t c h t o
Chronograph Mode and start up-counting
autom a ticall y, a nd it w i ll beep for 30
seconds.
How to Reload the Timer
+ To reload the timer with the current target
time for a new counting before the Watch
counts to zero, press the [L/R] button once
when the timer was stopped.
+ To start a new counting from a new target
time, set the timer again.
Regatta Timer Display
Counting Display
Stop Counting Display
digits start
counting
digits stop
counting
[S/S]
[L/R]
[S/S]
8.0 Dual Time Mode - Dual Time and Setting the Dual Time
Dual Time Display
+ The Watch includes a Dual Time Mode which
shows the current time for a second time
zone.
+ The second digits of the dual time is the
same as the current time.
+ When the Dual Time Display is selected, the
Watch will show the following items on the
display:
+ The dual time will appear on the middle
row.
+ The el a p s e o f s e c on d w i l l r e p r es e n t
ana logically by t he b ar-indicator whic h
around the display.
To Set the Dual Time
+ To select setting display, hold down the [M]
button for 2 seconds in Dual Time Mode, and
then the flashing "SET" icon will appear.
+ In setting display, press the [M] button to
chan ge the sele ction betw een h our a n d
minute.
+ When the digits are flashing (selected), press
the [S/S] / [L/R] button to increase / decrease
the number. (Hold down the button change
the number at a higher speed).
+ When the setting is completed, hold down the
[M] button to exit the setting display. The
Watch will also exit the setting display if NO
keystroke has been activated for 1 minute
Increase/ decrease
the number
Increase/decrease
the number at
a higher speed
hold [S/S] / hold [L/R][S/S] / [L/R]
User Preset Value Setting Sequence
hold
[M]
Setting Display
hourminute
hold
[M]
[M]
Dual Time Display
NOTE: This diagram exhibits the
c o n n e c tion b e t ween d i ff eren t
dis pla ys onl y, a nd he n ce t he
numbers showing on these display
do not conform to fact for some
instance.
Regatta Timer Alarm Sounds
digits
selected
(flashing)
10
50
9
9
8
8
40
7
7
6
6
30
5
5
4
4
20
3
3
2
2
10
1
1 0
minute(s)
seconds
second(s)
Chronograph auto-start
start
start
start
7.0 Regatta Timer Mode - Countdown Timer and the Quick-Set-Values
Regatta Timer Display
+ The Watch includes a Regatta Timer Mode which
measures the elapse of a fix period of time (target
time).
+ The timer starts down-counting from the target time to
zero and then it starts up-counting.
+ The target time can be set by using Quick Set Value
or User preset Value following the adjacent diagram.
+ When the Regatta Timer Display is selected, the
Watch wi ll show th e following items on the
display:
+ The Target time will appear on the middle row.
+ The current time will appear on the bottom row.
+ The elapse of second will represent analogically
by the bar-indicator which around the display.
The Quick-Set-Value
+ The Quick-Set-Value is a set of values w h i c h p r e -
installed into the Watch. These values can NOT be
changed by the user.
+ The Watch includes 6 Quick-Set Values, they are 1,
3, 5, 10, 15 and 45 minutes.
The User Preset Value
+ The User Preset Value is a value which can be set by
the user, and it can be set up to 99 hours 59 minutes
99 seconds.
+ Once the User Preset Value has been set, such as 30
minutes, it will store into the Watch for recall the next
time.
+ To set the User Preset Value, check the coming
chapter 7.1 for more detail.
Regatta Timer Display
1 min 3 min
45 min
5 min
10 min
15 min
Timer Setting Sequence
the indicator
flashing
the time which the
timer will countdown from
(hour, minute and second)
[L/R]
User
Preset
Value
Quick-Set-Value
[L/R]
[L/R]
[L/R]
[L/R][L/R]
[L/R]
Current Time
Beep Beep Beep Beep Beep Beep Beep Beep Beep Beep
Beep Beep Beep Beep Beep
Beep Beep Beep Beep Beep Beep Beep Beep Beep Beep-Beep for 30 sec.
To Next Page
Loading...