Need help?Do you have a question about the QuanSheng TG-K4AT and is the answer not in the manual?
General| Frequency Range | 400-470MHz |
|---|---|
| Output Power | 5W |
| Antenna Impedance | 50Ω |
| Battery Type | Li-ion |
| Weight | 220g (including battery) |
| Dimensions | 110x58x32mm |
| Operating Voltage | 7.4V DC |
Function of the Push-To-Talk button for transmitting.
Operation of the key for FM radio and alarm functions.
Controls for the flashlight and monitor function.
Functionality for shifting frequency bands or sending tones.
Overview of special function keys and their uses.
Usage of numerical keys for input and DTMF codes.
How to use the scan key for various scanning functions.
Operation of the power and volume control.
Meaning of the LED indicators for transmission and reception.
Ports for connecting accessories and computer.
Setting the noise squelch level for clear reception.
Adjusting the frequency increment for tuning.
Selecting between high and low power output.
Configuring power-saving modes to extend battery life.
Enabling voice-activated transmission without PTT.
Setting the operational bandwidth for transmission.
Adjusting the automatic backlight timeout.
Enabling simultaneous monitoring of two channels.
Configuring audible feedback for key presses.
Setting the time-out timer for transmissions.
Setting Digital Code Squelch for receiving.
Setting Continuous Tone-Coded Squelch for receiving.
Setting Digital Code Squelch for transmitting.
Setting Continuous Tone-Coded Squelch for transmitting.
Enabling voice prompts for radio operations.
Setting or checking Automatic Number Identification.
Configuring DTMF signal transmission for remote control.
Setting or managing radio signal codes.
Configuring scan resume behavior.
Setting PTT ID transmission mode.
Adjusting PTT ID transmission duration.
Setting display format for Channel A.
Setting display format for Channel B.
Preventing transmission on an occupied channel.
Enabling automatic keypad locking.
Setting frequency offset for repeaters.
Choosing the step frequency for tuning.
Selecting high or low output power.
Configuring battery saving modes.
Enabling voice-activated transmission.
Setting the radio's bandwidth.
Monitoring two channels simultaneously.
Adjusting the automatic backlight timer.
Enabling audible feedback for key presses.
Setting a limit for continuous transmission.
Setting Digital Code Squelch for receiving.
Setting Continuous Tone-Coded Squelch for receiving.
Setting Digital Code Squelch for transmitting.
Setting Continuous Tone-Coded Squelch for transmitting.
Enabling voice prompts for radio operations.
Setting or checking Automatic Number Identification.
Configuring DTMF signal transmission.
Setting radio signal codes.
Configuring scan resume behavior.
Setting PTT ID transmission mode.
Adjusting PTT ID transmission duration.
Setting display format for Channel A.
Setting display format for Channel B.
Preventing transmission on an occupied channel.
Enabling automatic keypad locking.
Setting frequency offset for repeaters.
Setting deviation between receiving and transmitting frequencies.
Storing frequencies and parameters into memory channels.
Deleting stored channels and information.
Choosing backlight color for standby mode.
Choosing backlight color for receiving mode.
Choosing backlight color for transmitting mode.
Setting alarm modes (tone, code, site).
Switching between VHF and UHF frequency bands.
Monitoring dual-watch operation across bands.
Eliminating carrier wave audio after transmission.
Adjusting tail tone elimination for repeater communication.
Setting delay time for tail tone elimination.
Configuring the display mode shown at power-on.
Enabling a beep tone at the end of a conversation.
Performing factory reset for menu and channel settings.
Initializing the radio using VFO mode settings.
Performing a full initialization of all settings.
Manually locking and unlocking the radio's keypad.
Operating the radio's FM broadcast receiver function.
Activating a rapid alarm function.
Turning the flashlight on and off.
Using the monitor function to listen for signals.
Copying radio settings to another unit via cable.
Switching between channel and frequency modes.
Sending a 1750Hz call tone for repeaters.
Shifting transmit and receive frequencies.
Scanning frequencies based on set step frequency.
Scanning through programmed channels.
Automatically searching for FM radio stations.
Searching for and storing CTCSS/DCS codes.
Using cursor keys to modify frequency/channel parameters.
Quickly switching between high and low power modes.
To Next Page