QUORUM INTERNATIONAL 7-501-0

To Next Page

Model: 7-501-0

Fig. 1

Fig. 2

Fig. 3

RECEIVER

AC SUPPLY

BLACK

WHITE

BARE GREEN

WHITE

BLUE BLUE

BLACK

RECEIVER

INSTALLING RECEIVER IN CEILING FAN

A: Safety precautions:

● WARNING: HIGH VOLTAGE! Disconnect source of

electrical power by removing fuse or switching off circuit

breaker.

● Do not use with solid state fans.

● Electrical wiring must meet all local and national electrical code

requirements.

● Electrical source and fan must be 115/120 volt, 60Hz. Maximum

fan motor amps: 1.0. Maximum light watts: 300W Incandescent

and Halogen.

● Household electrical power can cause serious injury or death!

B: Installing receiver in fan:

a. Remove electrical power from the circuit.

b. Disconnect existing wiring between ceiling fan and supply at

electrical junction box.

c. Lay the black antenna wire on top of the receiver, and put the

receiver in the mounting bracket. (Fig. 1)

d. Make connections as follows, using the wire nuts supplied

(Fig. 2):

CONNECT

Green fan wire

Black receiver wire (AC IN L)

White receiver wire (AC IN N)

White receiver wire (TO MOTOR N)

Black receiver wire (TO MOTOR L)

Blue receiver wire (FOR LIGHT)

………......…………………….Bare supply wire

...……....……Black supply wire

..……....…...White supply wire

..…….......White fan wire

..……....…Black fan wire

..……...……..Blue light wire

HANDHELD REMOTE CONTROL

If there are wires with different colors, have this unit installed

by qualified licensed electrician.

e. Push all connected wires up into junction box.

f. Lay the black antenna wire on top of the receiver, and put the

receiver in the mounting bracket. (Fig. 2)

g. Reinstall all canopy on the mounting bracket

C. Installing reverse module in ceiling fan

a. Disconnect the switch cup assembly from the bottom of the

fan. (If the fan is a new installation, this cup will not be

attached to the fan yet)

b. Connect the ‘female’ cannon plug on the reverse module to the

cannon plug from the fan flange (Fig. 3)

c. Connect the ‘male’ cannon plug on the reverse module to the

cannon plug in the switch cup assembly.

d. Secure the switch cup assembly to the fan as described in the

fan installation instructions.

SCREWS

SWITCH CUP PLATE

CANNON PLUGS

REVERSE MODULE

SWITCH CUP

ASSEMBLY

Need help?

Do you have a question about the QUORUM INTERNATIONAL 7-501-0 and is the answer not in the manual?

This document describes the installation and operation of the Quorum International Handheld Remote Control for ceiling fans, model 7-501-0.

Function Description:

The Quorum International Handheld Remote Control system is designed to provide wireless control over ceiling fan functions, including fan speed, light operation (on/off and dimming), and fan direction (forward/reverse). It consists of a receiver unit that is installed within the ceiling fan's canopy and a handheld transmitter for user interaction. The system features an automatically learned pairing process, eliminating the need for manual frequency switches.

Important Technical Specifications:

Power Requirements: The electrical source and fan must be 115/120 volt, 60Hz.
Maximum Fan Motor Amps: 1.0 Amp.
Maximum Light Watts: 300W for Incandescent and Halogen bulbs.
Remote Battery: 3-volt battery (CR2032) for the handheld transmitter.
Code Combinations: The system offers 65,000 different code combinations for secure and interference-free operation.
Operating Range: The distance between the transmitter and receiver should not be greater than 30 feet for best performance.
Light Compatibility: The "DIM" setting is for dimmable LED bulbs only. The "ON/OFF" setting provides light on/off functionality without dimming.

Installation Features:

The installation process involves integrating the receiver unit into the ceiling fan's mounting bracket and connecting it to the fan's electrical wiring.

Safety First: Always disconnect the electrical power source (by removing a fuse or switching off a circuit breaker) before beginning installation to prevent serious injury or death.
Compatibility: Do not use this remote control system with solid-state fans. All electrical wiring must comply with local and national electrical code requirements.
Receiver Placement: The receiver is placed within the mounting bracket, with the black antenna wire laid on top of it.
Wiring Connections (using supplied wire nuts):
- Green fan wire to Bare supply wire.
- Black receiver wire (AC IN L) to Black supply wire.
- White receiver wire (AC IN N) to White supply wire.
- White receiver wire (TO MOTOR N) to White fan wire.
- Black receiver wire (TO MOTOR L) to Black fan wire.
- Blue receiver wire (FOR LIGHT) to Blue light wire.
- Note: If wire colors differ, a licensed electrician should perform the installation.
Wire Management: Push all connected wires into the junction box.
Canopy Reinstallation: Reinstall the canopy onto the mounting bracket after all connections are made.
Reverse Module Installation (if applicable):
- Disconnect the switch cup assembly from the bottom of the fan.
- Connect the 'female' cannon plug on the reverse module to the cannon plug from the fan flange.
- Connect the 'male' cannon plug on the reverse module to the cannon plug in the switch cup assembly.
- Secure the switch cup assembly to the fan as per the fan installation instructions.

Usage Features:

The handheld remote control offers intuitive operation for various fan and light functions.

Remote Pairing:
- Ensure the fan's power is off.
- Install the 3-volt CR2032 battery into the transmitter, ensuring the positive (+) side faces up.
- Restore power to the fan.
- Press and hold the "FAN OFF" button for approximately 5 seconds, then release.
- If an optional light kit is installed, it will flash twice, and the signal light on the remote will illuminate, indicating successful pairing.
Fan Speed Control:
- "H" button: Sets fan to high speed.
- "M" button: Sets fan to medium speed.
- "L" button: Sets fan to low speed.
Fan Off:
- "FAN OFF" button: Turns the fan off.
Light Control and Dimming:
- "LIGHT" button: Turns the light ON or OFF.
- Press and hold the "LIGHT" button to dim or brighten the light. Release the button at the desired brightness.
- The light key has an auto-resume feature, returning to the last set brightness level.
Fan Direction (Forward/Reverse):
- "REVERSE" button: Toggles the fan direction (forward for warm weather, reverse for cool weather).
- Note: To operate the reverse function, press the reverse button while the fan is running.
Timer Function:
- "2H", "4H", "8H" buttons: Automatically turn the fan off after 2, 4, or 8 hours, respectively.
- Note: The timer function is only active when the fan speeds are on; it does not include the light.
- To cancel the timer, press the "FAN OFF" button and restart the fan speed.
Light Dimming Dip Switch:
- A "DIM" / "ON/OFF" dip switch (located inside the remote, accessible by removing the battery cover) allows selection between dimmable light functionality (for LED bulbs only) or simple on/off light functionality (no dimming).

Maintenance Features:

Battery Replacement: The handheld transmitter uses a 3-volt CR2032 battery. To replace, remove the set screw on the back of the transmitter, take out the battery cover, and insert the new battery with the positive (+) sign facing up. Use a suitable screwdriver to loosen or tighten the screws.
Storage: If the transmitter will not be used for long periods (months), remove the batteries to prevent damage.
Antenna: For best performance, ensure the black antenna on the receiver unit remains extended and is not tangled with other electrical wires.