What to do if there is no echo on RADIO HOLLAND RHRS-2014?
If the power is on and you operated the STBY/TX key to transmit, but marks and characters appear without any echo on your RADIO HOLLAND Radar, you should: * Check that the antenna cable is properly fastened. * Adjust the GAIN and STC levels. * Adjust the echo brilliance.
What to do if the RADIO HOLLAND RHRS-2014 Radar does not operate after turning on?
If the power of your RADIO HOLLAND Radar is on but the radar doesn't operate at all, the panel board might be the cause. Consider replacing the panel board.
What to do if RADIO HOLLAND RHRS-2014 Radar picture is not updated or freezes?
If the picture on your RADIO HOLLAND Radar is not updating or freezes, try the following: * Check that the signal cables are fastened. * Replace the SPU board. * Turn the radar off and on again.
Why is the RADIO HOLLAND RHRS-2014 Radar sensitivity poor even when tuned correctly?
If your RADIO HOLLAND Radar is correctly tuned but has poor sensitivity, check the magnetron current with the radar transmitting on 48 nm range. Also, clean the radiator if it's dirty.
What to do if RADIO HOLLAND RHRS-2014 Radar cannot be turned on?
If you cannot turn on the power of your RADIO HOLLAND Radar, you should: 1. Replace the blown fuse. 2. Correct the wiring and input voltage if there's an issue with the mains voltage/polarity. 3. Replace the power supply board if it's faulty.
What to do if there is no noise or echo on RADIO HOLLAND Radar?
If you set the [GAIN] to maximum with [STC] and [RAIN] settings at minimum and marks and indications appear without noise or echo on your RADIO HOLLAND Radar, you should: * Replace the IF amplifier. * Check the continuity and isolation of the coaxial cable. * Replace the video amplifier.
Why is there no echo in short range on my RADIO HOLLAND RHRS-2014?
If marks, indications, and noise appear on your RADIO HOLLAND Radar, but there is no echo in short range, you should: * Check the magnetron current. * Replace the modulator board. * Replace the SPU board.
What to do if RADIO HOLLAND Radar antenna is not rotating?
If the antenna on your RADIO HOLLAND Radar is not rotating, you should: * Check the setting of the antenna switch (refer to the Installation manual). * Check the voltage for the motor and replace the PSU board if necessary. * Ensure the antenna switch on the antenna unit is ON. * Replace the motor if there's a gear mechanism issue. * Replace the RF_TB board.
Why is there no picture or malfunction via the interswitch of RADIO HOLLAND Radars?
If there is no picture or malfunction via the interswitch of the radars, confirm the connection of the LAN cables and the hub, then turn on the power of the radar. Also, check if some radars have the same IP address and change addresses in case of duplication. Restart all radars on the network.
What to do if RADIO HOLLAND RHRS-2014 Radar keys are not responding?
If there is no response when a key is pressed on the RADIO HOLLAND Radar, long press the POWER key for approximately seven seconds to turn off the power. Then, turn the power on again.
Hazard warning for radar antenna radiation and safe distances.
Safety warnings regarding electrical shock, antenna rotation, water leaks.
Overview of the radar's physical controls and their functions.
Step-by-step instructions for powering the radar on and off.
Procedure for switching between stand-by and transmit modes.
How to navigate and use the radar's menu system.
Methods for tuning the radar for optimal performance.
Explanation of River and Sea operating modes.
Procedure for changing the radar's display range.
Explanation and adjustment of pulse width settings.
Methods for adjusting receiver sensitivity (gain).
Techniques for minimizing sea clutter on the display.
Techniques for minimizing rain clutter on the display.
Using FTC to suppress spurious echoes and rain clutter.
Measuring target range using fixed rings and VRM.
Measuring target bearing using EBL and selecting bearing reference.
Using the interference rejecter to reduce radar interference.
Setting alarms for targets entering or exiting specific zones.
Understanding alarm indications and error messages.
Features and activation of the docking mode.
Combining two radar displays for enhanced situational awareness.
Customizing function keys for quick access to features.
Creating and managing marks and lines on the radar display.
Enabling or disabling the Target Tracking display.
Procedures for acquiring and tracking targets manually and automatically.
Steps for manually acquiring radar targets.
Setting up acquisition zones for automatic target acquisition.
Methods for canceling target tracking.
Displaying detailed data for tracked targets.
Viewing a list of tracked targets with key information.
Procedure for setting an automatic acquisition zone.
Method to stop tracking all acquired targets.
Showing or hiding the AIS display and its functions.
Filtering unnecessary AIS targets from the display.
Activating specific or all AIS targets manually.
Filtering lost targets based on range or speed criteria.
Steps to cancel tracking for specific targets.
Setting alarms for Closest Point of Approach and Time to CPA.
Automatically activating AIS targets based on CPA settings.
Automatically activating AIS targets based on CPA settings.
Setting AIS CPA/TCPA alarms.
Setting AIS CPA/TCPA alarms.
Methods for adding marks and lines to the radar map.
Routine maintenance tasks to keep the equipment in good condition.
Performing system checks to diagnose operational issues.
Common problems and their solutions for user-level troubleshooting.
Procedures for hardware/software troubleshooting by qualified personnel.
Details on radar range, pulse length, and PRR for different modes.
General| Brand | RADIO HOLLAND |
|---|---|
| Model | RHRS-2014 |
| Category | Radar |
| Language | English |
To Next Page