RAM R7 Series User Manual

1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
125
SURFACE
FINISH:
SURFACE FEATURES: MACHINED PARTS ONLY
T.I.R
 .005 PERPENDICULAR  .015
FLATNESS .010 PARALLEL
 .015
120
X.X ±0.03
X.XX ±0.015
X.XXX ±0.005
FRACTION ± 1/16
ON ALL
MACHINED
SURFACES
DIMENSIONS:
BREAK ALL SHARP EDGES
UNLESS OTHERWISE SPECIFIED:
ALL DIMENSIONS ARE IN INCHES
AND ALL TOLERANCES ARE AS STATED
3rd ANGLE PROJECTION
DO NOT SCALE
R7
RS1123
LBS.
410580
EST. FINISHED
WEIGHT
ORIGINAL JOB NO.
MODEL NUMBERNEXT ASSEMBLY
ANGLES: ±
0.5°
APVD:
M.WEHMEYER
M.TROYER
M.TROYER
2/20/2019
2/20/2019
CKD:
M.TROYER
DWN:
ENG:
2/20/2019
TITLE:
2/20/2019
ASSEMBLY, R7 LEVELWIND DRIVE
SIZE:
AR10568
410568
SHT:SCALE:
DWG NUMBER: REV:
PART NUMBER:
N/A
OF
1
0
2
B
THIS DRAWING IS THE PROPERTY
OF RAM ITC. THE DESIGN AND DATA
SHOWN INCLUDES PROPRIETARY
INFORMATION THAT DESCRIBES
RAM ITC. PRODUCTS. THE
BORROWER BY RECEIPT AND
RETENTION OF THE DRAWING
AGREES, THAT EXCEPT AS
EXPRESSLY AUTHORIZED IN
WRITING BY RAM ITC., IT WILL (1)
ONLY USE THE DRAWING OR THE
DESIGN AND DATA SHOWN FOR THE
PURPOSE INTENDED BY RAM ITC; (2)
NOT LOAN, REPRODUCE, EXHIBIT OR
DISTRIBUTE THE DRAWING OR ANY
COPY OF THE DESIGN OR DATA
SHOWN FOR USE BY ANY OTHER
THAN RAM ITC., AND (3) UPON
DEMAND RETURN THE DRAWING,
ALL COPIES AND ALL MATERIAL
COPIES THEREFROM.
.2 PLUG FITTING, -8 M SAE ORB HOLLOW HEX3FP20052
-
31
.0 30mm DIN 471 SNAP RING
1
AG81118
-
30
.0 RADIAL SHAFT SEAL, 60x85x8 CRW1 R
1
AG81117
-
29
.0 BUNA-N O-RING1AG80186
-
28
.0 BUNA-N O-RING1AG80185
-
27
.0 BUNA-N O-RING2AG80172
-
26
.0 O-RING2AG80604
-
25
.4
3/8-16 X 2 SHCS
5FQ00955
-
24
1.1
1/2-13 X 3-3/4 HHCS
4FQ02054
-
23
.2 1/2-13 HEX NUT
4
FQ12252
-
22
.1
1/2 FLAT WASHER
4
FQ12735
-
21
.1
1/2 LOCKWASHER
4FQ11202
-
20
.4 DEEP GROOVE BAL BEARING1AG81116
-
19
2.0 TAPER ROLLER BEARING, F-TO-F MATCHED
1
AG81115
-
18
.7
1/4-20 X 4 3/4 SHCS
10FQ00557
-
17
.1
#10-32 X 3/8 SHCS
8FQ00305
-
16
2.0 RING GEAR1AG81081
-
15
.1
4L60E/700R4 SUN GEAR THRUST BEARING
1
AG81082
-
14
3.2
ASEMBLY, 4L60E/700R4 PLANETARY
1
AG81080
-
13
2.9
ASSEMBLY, 4L60E/700R4 FRONT RING GEAR
1AG81081
-
12
1.0 LEVEL WIND SCREW BEARING ADAPTER1AR1055541055511
.2 LEVEL WIND SCREW BEARING RETAINER2AR1055641055610
7.8 RETAINER, LEVELWIND SCREW DRIVE
1
AR105574105579
12.9 LEVEL WIND DRIVE SCREW1AR105584105588
14.2
MOUNTING PLATE, GEARBOX/MOTOR
1AR105594105597
56.6 AIR MOTOR ASSEMBLY MODEL R4M20
1
AG078154078156
.9 ASSEMBLY, SUN DRIVE GEAR
1
AR10627410627
5
4.5 MOUNTING SPACER, LEVELWIND MOTOR1AR105604105604
1.6 COVER, LEVELWIND GEARBOX1AR105614105613
1.0 ASSEMBLY, INTERMEDIATE SUN GEAR
1
AR105644105642
3.1 MODIFICATION, PLANET CARRIER
1
AR10565410565
1
Parts List
WT (LBS)
EXPANDED DESCRIPTIONDESCRIPTIONQTYPART NO.DRAW NO.ITEM
A
A
REVISION HISTORY
REV DESCRIPTION DATE ECN
0INITIAL RELEASE
2/20/2019
NA
NOTES:
TORQUE ALL FASTENERS ACCORDING TO RAM PROCESS SPECIFICATION PS-100013
WHERE APPLICABLE.
1.
APPLY LOCTITE 277 TO FASTENERS AS REQUIRED PER MANUFACTURERS INSTRUCTIONS.
2.
FILL HYDRAULIC MOTOR CASE WITH HYDRAULIC OIL THROUGH THE CASE
VENT PORT PRIOR TO TEST.
3.
THOROUGHLY COAT FRAME TIE BAR TO FRAME CONNECTIONS AND ASSOCIATED
FASTENERS WITH MARINE GRADE NEVER-SEIZE.
4.
19
9
7
3
6
6
6
31

RAM R7 Series Specifications

General

Gear Train	3-Stage Planetary
Series	R7
Line Pull	7000 lbs
Remote Control	Wireless Remote
Battery Leads	2 gauge
Rope	3/8" Synthetic Rope