R&S ESU Series - Page 762

Operating Manual 1302.6163.12 - 03 6.323
R&S ESU Remote Control – Description of Commands
Differences in GPIB Behavior between the FSP and the FSE Families of Instruments
R&S
ESU
[SENSe<1|2>:]DETector<1...3>[:FUNCtion] APEak |NEGative |
POSitive | SAMPle |
RMS | AVERage |
QPEak
R&S ESU: number of
traces restricted to 3;
detector settings
correspond to selected
screen
FSE: Qpeak not
available
ESIB [SENSe<1|2>:]DETector<1..4>[:FUNCtion] APEak |NEGative |
POSitive | SAMPle |
RMS | AVERage |
QPEak
R&S
ESU
FSE [SENSe<1|2>:]DETector<1...3>[:FUNCtion]:AUTO ON | OFF number of traces
restricted to 3
FSET [SENSe<1|2>:]DETector<1...4>:PSTRetch:AUTO ON | OFF not available for
R&S ESU
FSET [SENSe<1|2>:]DETecto<1...4>r:PSTRetch[:
STATe]
ON | OFF not available for
R&S ESU
ESIB [SENSe<1|2>:]DETector<1...4>:RECeiver[:
FUNCtion]
POSitive |NEGative|
RMS | AVERage |
QPEak
not available for
R&S ESU
FSET [SENSe<1|2>:]DETector<1...4>:RECeiver[:
FUNCtion]
POSitive | NEGative |
RMS | AVERage
not available for
R&S ESU
FSE [SENSe<1|2>:]FILTer:CCITt[:STATe] ON | OFF not available for
R&S ESU and FSET
FSE [SENSe<1|2>:]FILTer:CMESsage[:STATe] ON | OFF not available for
R&S ESU and FSET
FSE [SENSe<1|2>:]FILTer:DEMPhasis:LINK DISPlay | AUDio not available for
R&S ESU and FSET
FSE [SENSe<1|2>:]FILTer:DEMPhasis:TCONstant <numeric_value> not available for
R&S ESU and FSET
FSE [SENSe<1|2>:]FILTer:DEMPhasis[:STATe] ON | OFF not available for
R&S ESU and FSET
FSE [SENSe<1|2>:]FILTer:HPASs:FREQuency 30 Hz | 300 HZ not available for
R&S ESU and FSET
FSET [SENSe<1|2>:]FILTer:HPASs:FREQuency 10 kHz | 1 kHz | 100 Hz not available for
R&S ESU
FSE [SENSe<1|2>:]FILTer:HPASs[:STATe] ON | OFF not available for
R&S ESU
FSE [SENSe<1|2>:]FILTer:LPASs:FREQuency 3 kHz| 15 kHz not available for
R&S ESU and FSET
FSE [SENSe<1|2>:]FILTer:LPASs[:STATe] ON | OFF not available for
R&S ESU and FSET
FSET [SENSe<1|2>:]FILTer:NOTCh[:STATe] ON | OFF not available for
R&S ESU
FSET [SENSe<1|2>:]FM[:DEViation]:RANGe:UPPer ON | OFF not available for
R&S ESU
FSET [SENSe<1|2>:]FM[:DEViation]:RANGe[:UPPer] <numeric_value> not available for
R&S ESU
Devices Command (Sheet 35 of 47) Parameter Notes