The REBEL RENEGADE is a gaming chair designed for comfort and adjustability, featuring a range of components and functions to enhance the user experience. This instruction manual details the assembly process, operating instructions, safety guidelines, and maintenance tips for the chair.
Function Description:
The REBEL RENEGADE chair serves as a comfortable and ergonomic seating solution, primarily for gaming or office use. It is designed to support a single user and offers multiple adjustment features to customize the seating position according to individual preferences. The chair's design emphasizes stability, adjustability, and user safety.
Important Technical Specifications:
- Model: RENEGADE
- Weight Limit: Not to exceed 300 lbs.
- Bolts:
- M5x8mm (Quantity: 4)
- M8x25mm (Quantity: 20)
- Components:
- Casters (Quantity: 5)
- Star Base (Quantity: 1)
- Gas Lift (Quantity: 1)
- Lift Cover (Quantity: 1)
- Left Plastic Cover Set (Quantity: 1, includes E1 and E2)
- Right Plastic Cover Set (Quantity: 1, includes F1 and F2)
- Angle Adjusters (Quantity: 2)
- Seat Plate (Quantity: 1)
- Seat Cushion (Quantity: 1)
- Back Cushion (Quantity: 1)
- Armrests (Quantity: 2, Left and Right)
- Wrench (Quantity: 1)
- Plastic Caps (Quantity: 2)
- Warranty: 1 Year for defects in material or manufacture.
Usage Features:
Assembly Instructions:
The assembly process is broken down into ten steps:
- Step 1: Casters Installation: Turn the Star Base upside down and press the five Casters (A) into the holes at the end of each base leg.
- Step 2: Gas Lift Installation: Turn the Star Base upright. Insert the Gas Lift (C) into the center hole of the Star Base. Place the Lift Cover (D) on top of the Gas Lift.
- Step 3: Bolt Removal: Remove all M8x25mm Bolts from the seat cushion (I) and back cushion (J) before proceeding.
- Step 4: Armrest Attachment to Seat Cushion: Attach the two Armrests (K) to the Seat Cushion (I) using eight M8x25mm bolts. Ensure the left and right armrests are in their correct positions and tighten with the provided Wrench (3).
- Step 5: Seat Plate Attachment: Align the Seat Plate (H) with the bottom of the Seat Cushion (I), ensuring the front of the seat plate faces the front of the seat cushion. Attach the seat plate using four M8x25mm bolts and tighten.
- Step 6: Seat Cushion to Gas Lift Connection: Turn the Seat Cushion upright and align the center hole of the Seat Plate with the Gas Lift. Push the seat cushion down firmly onto the gas lift until the connection is secure.
- Step 7: Angle Adjusters to Seat Cushion: Align the Angle Adjusters (G) with the pre-drilled holes on the Seat Cushion. Attach the angle adjusters to the cushion using M8x25mm bolts. Important: Tighten these bolts to 50%, not 100%, at this stage.
- Step 8: Angle Adjusters to Back Cushion: Take the Back Cushion (J) and align the Angle Adjusters with the pre-drilled holes on the back cushion. Attach the angle adjusters to the back cushion using M8x25mm bolts.
- Step 9: Final Tightening: Adjust the balance of the chair and then fully tighten all bolts on the angle adjusters.
- Step 10: Plastic Cover Attachment: Attach the Left Plastic Cover Set (E1, E2) and Right Plastic Cover Set (F1, F2) using four M5x8mm bolts.
Operating Instructions:
- 1. Seat Height Adjustment:
- A paddle-shaped lever is located on the right side of the chair.
- To raise: Take your weight off the chair and lift the lever up.
- To lower: While seated, lift the lever up.
- Note: At the proper height, your feet should rest flat on the floor.
- 2. Tilt Tension Adjustment:
- A long stem with a knob is located under the seat cushion.
- To increase tension: While seated, turn the knob forward (toward the '+' sign).
- To decrease tension: While seated, turn the knob backward (toward the '-' sign).
- Note: Adjust tilt tension to control the resistance felt when leaning back.
- 3. Tilt Lockout:
- To allow chair to tilt back: Pull the control handle out.
- To stop chair from tilting: Sit forward, then push the control handle in.
- Note: At the proper height, your feet should rest flat on the floor.
- 4. 4D-Function Armrest: The armrests offer four directions of adjustment:
- Up and Down
- Left and Right
- Forward and Backward
- Rotate
- 5. Backrest Recline:
- Pull the recline lever fully and lean back slowly until the desired angle is achieved.
- Then, slowly return the lever to its starting position, ensuring it locks back in place.
Maintenance Features:
- Bolt and Screw Check: Every 6 months, check all bolts and screws to ensure they are tight.
- Cleaning: Spot clean only using a damp towel and a mild cleaner. Always test on a small, obscure area of fabric first.
- Safety Guidelines:
- Do not stand on the chair or use it as a stepladder.
- Use the product for seating one person at a time.
- Do not use the chair unless all bolts and screws are firmly secured.
- Avoid contact with sharp objects to prevent puncturing the fabric.
- Sit in the center of the chair with your back to the backrest.
- Do not sit at the front edge of the chair.
- Do not stand on the chair.
- Do not use the chair with more than one person.
- Do not push the chair around when a person is sitting in it.
- Do not push down on the backrest when a person is reclined.
- Do not place all your weight on the backrest only.
- Do not place your hand or fingers near the recline mechanism.
Warranty and Disclaimers:
- Warranty Agreement: REBEL provides a 1-year warranty for defects in material or manufacture, offering repair or replacement service based on the invoice or warranty card date.
- Disclaimers: REBEL is not liable for damage to life, limb, or property caused by or during the use of its products. REBEL's warranty liability is limited to repair or replacement, with the decision solely belonging to REBEL.
Need help?
General
To Next Page