Red Shed 2085884 - User Manual

RS 10FT SKELETON
1 2 3
PACKAGE CONTENTS
Thank you for purchasing the Life-Skeleton with Lighted Eyes!
Below you’ll nd assembly instructions and other information to get
maximum enjoyment from your purchase!
Please read instructions carefully before use.Retain for future reference.
Front Base Back Base Right Foot Left Foot Right Fibula
Left Fibula
Right Femur
Left Femur
Skull Ground Stakes
T-Bar
Support Pole
Pelvis Ribcage Spine
Right Arm
Left Arm
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
PREPARATION
Estimated Assembly Time: 15 - 20 minutes
Before assembling the product, carefully remove all parts from the box and lay out on a at surface.
Make sure all parts are present. Compare parts with package contents list.
If any part is missing or damaged, do not attempt to assemble, install or operate the product.
Read through directions before assembling.
2. Take right foot (C) and place the heel over the
post on the front base (A). Repeat the process
with the left foot (D) and back base (B).
1. Set front and back base parts (A and B) on a
level and stable surface. Connect the two base
parts and ensure the pushpins are locked
in place.
3. Place right bula (E) onto the right foot (C).
Repeat the process for the left bula (F) and the
left foot (D).
8. Connect the ribcage (K) and spine (L) by
placing the ribcage (K) upside down on a at
surface. With the spine (L) upside down,
slide it onto the ribcage (K) and lock into
place.
7. Ensure the pelvis (J) is in the upright
position and locked into place with the pole
of the T-bar (I) positioned upward.
9. Connect the wires between ribcage (K)
and spine (L).
4. Place right femur (G) onto the right bula
(E). Repeat the process for the left femur (H)
and left bula (F).
5. Insert the T-bar (I) into the openings
of the lower pelvis (J).
6. Connect the pelvis (J) and T-bar (I) to the upper femurs (G,H) by
sliding the "T" into the corresponding openings of the bones. Push
together and lock into place.
10. Lay at the connected ribcage and spine (K,L) to attach the arms (M,N).
Insert the right arm (M) into the upper body (K,L). Repeat process for the left
arm (N).
11. Insert skull (O) into the top of the body.
13. The recommended method to attach the upper body and lower body is
to lay each section at. Place the assembled upper body onto the item's box.
Lift the lower body and slide the T-bar (I) into the spine (L) and gently lock
into place.
12. Connect the wires between skull (O) and assembled body.
A. Front Base 1pc
B. Back Base 1pc
C. Right Foot 1pc
D. Left Foot 1pc
E. Right Fibula 1pc
F. Left Fibula 1pc
G. Right Femur 1pc
H. Left Femur 1pc
I. T-Bar Support Pole 1pc
J. Pelvis 1pc
K. Ribcage 1pc
L. Spine 1pc
M. Right Arm 1pc
N. Left Arm 1pc
O. Skull 1pc
P. Ground Stakes 5pcs
A
LABELED PARTS
A
B
B
C
D
C
C
D
D
E F
E F
E F
J
J
J
J
K
K
K
K
K
K
K
K
L
L
L
M
N
G H
G
G
H
G H
H
I
I
I
I
I
O
O
O
P
M
M
M
1 2 3
7 8 9
4 5 6
10
11 12
13
Instruction Manual
SKU# 2085884

Red Shed 2085884 Specifications