Remington HC5950 - Page 3

4 5
ENGLISH
ENGLISH
•Topreservethelifeofyourbatteries,letthemrunoutevery6monthsthenrechargefor
90 minutes.
, CHARGING VIA STANDARD ELECTRICAL SOCKET
•Ensuretheproductisswitchedo.
•Connectthechargingadaptortotheproductandthentothemains.
•Whenchargingthedigitaldisplaywillindicatetheunitischarging
•Allow90minutesforacompletecharge.
, USB
•ConnectyourUSBcabletotheUSBportonyourpowersource.
•ConnecttheUSBcabletoyourappliance.
•DonotruntheclipperwhileconnectedtoaUSBport.Itwillonlyrunoitsbatteriesin
this condition and stop charging.
, CORDED USE
•Connectthechargingadaptortotheproductthentothemains.
•Whenthecordisconnectedtothemains,adigitaldisplaywillbedisplayedonthe
appliance.
•Theunitwillonlyrunincordedmodewhenconnectedtothemainsusingthesupplie
•Remingtonpoweradaptor,otherUSBchargerswillonlychargetheunit
A CAUTION
Extendedmainsonlyusewillresultinthereductionofthebatterylife.
, WARNING
TheappliancecannotbeoperatedincordedmodewhileconnectedtoaPCviatheUSBport.
, CORDLESS USE
Whentheunitisswitchedonandfullycharged,theproductcanbeusedincordlessmodefor
up to 40 minutes.
F HOW TO USE
, USING THE TOUCH SCREEN
, ADJUSTING THE TRIM LENGTH
• Firstselectwhichhaircomb1,2or3forthelengthrangedesired.
•Comb1(1.5mm),comb2(3mmto23mm),Comb3(22mmto42mm).Usingthecomb
selectionswitchsetthesystemtomatchthecorrespondingcomb.
• IfComb1isselected,thedisplaywillalwaysshow1.5mmor#0,asthereisno
mechanical adjustment
• ForComb2and3,thetouchbuttonscanbeusedtoadjusttothedesiredcuttinglength
followingthestepsbelow
• Withcomb2and3,installedontotheproductandthecorrespondingcombswitch
selectedadjustmentcanbegin.Alsoensurethatthelockbuttonisintheunlocked
position.
Note: Ifaredwarninglightisvisiblethroughthecombwheninstalled,thisisindication
thatthecombselectionswitchisonthewrongsetting.
• Pressandholdthearrowuptoincreasethecuttinglengthanddowntodecreaseit.The
combwillmovetoreacheachsetting,thelengthswillchangeasyouholdtheup/down
arrow,andthesettingnumberwillappearonthedigitaldisplay.
• Selectthedesiredboostlevelbypressingtheboostbuttonwiththelockinthe
unlockedposition.Thedisplaywillindicatethelevel.
• Oncethedesiredlengthandboostlevelarereached,lockthesystemusingthelock
switch.Thedisplayshouldshowaclosedlock,andthecurrentlengthsettingandboost
level.Proceedtousetheclipper
 Note:Adjustmentstolengthandboostcanbedoneanytimethelockswitchissetto
unlock.Settingcanbedonewiththemainmotoro,ifthepowerbuttonispresseda
secondtime.Toturnthemainmotorbackonthepowerbuttonneedstobepressed
again.
• Pressandholdthebatteryicontodisplaytheremainingbatterytimeinminutesonthe
digitaldisplay.Thiscanbeusedwhilsttheapplianceislocked.
, SWITCHING BETWEEN UNITS OF LENGTH (mm, #)
Holdthepowerbuttonfor3seconds,thedisplaywillshowthechangebetweenmmand#,at
thistimereleasethepowerbutton.Thesettinghasbeenchanged.
Note:Iftheusercontinuestoholdthepowerbuttonfor8seconds,thesystemwillenterreset
mode
A CAUTION
Oncethedigitaldisplaychangesfrommmtogradenumber,releasethepowerbuttontoavoid
aninadvertentrestart.
NOTE:Thecombmustbeattachedtotheapplianceinordertousethehairlengthselector.To
achieve0.4mmthecombmustberemoved.
, BEFORE STARTING THE CUT
• Inspecttheclippermakingsurethatitisfreefromhairanddirt.
• Seatthepersonsothattheirheadisapproximatelyatyoureyelevel.
• Beforecutting,alwayscombthehairsoitistanglefreeanddry.
, TO ATTACH A COMB
• Holdthecombwithitsteethupward
• Guidethecombrailsintotheslotsonthesideoftheclipperhead.Thenpushthecomb
down until it seats on the adjustment arm.
, TO REMOVE THE COMB
• Holdingtheclipperwiththebladesfacingawayfromyou,rmlypushthecombupward
andawayfromtheblades.