XR7000
Use and Care Guide
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic precautions should always
be observed, including the following. Please read all instructions
before using this shaver.
WARNINGS
To reduce the risk of burns, fire, electric shock, or injury to persons:
• When connecting the charging unit to a power source outside
of the USA or Canada, use a plug adapter suitable for the power
outlet. This device has a charging adapter that will work with
worldwide 100V-240V power outlets.
• Only use the power adapter provided with this device.
• Do not reach for the appliance if it has fallen into water while
plugged into the power source. Unplug from the power source
at the wall immediately.
• Shaver may be rinsed under water or used in the shower,
but never use the charging unit in the shower.
• Detach the shaver and charging unit from the power source
before cleaning.
• Except when charging, always unplug this appliance
immediately after using.
• When recharging place in a safe position, out of the reach of
children and pets.
• Close supervision is necessary when this appliance is used by,
on, or near children or individuals with certain disabilities or
special needs.
• Use this appliance only for its intended use as described in
this manual.
• Do not use attachments not recommended or provided by
the supplier.
• Never operate this appliance if the electrical cord is frayed or
the plug is damaged.
• Keep the electrical cord away from heated surfaces.
• Never drop or insert objects into any of the appliances openings.
• This appliance is intended for household use only.
• Do not use outdoors, or operate where aerosol (spray) products
are being used, or where oxygen is being administered.
• Always attach the plug to the appliance, then to the wall outlet.
To disconnect, turn all controls to OFF, then remove plug from
outlet.
• Always pull on the plug body to unplug the appliance from the
wall socket. Never pull on the electrical cord.
• Do not plug in or unplug this appliance when your hands are wet.
• Do not use extension cords or a voltage converter with this
appliance.
• Do not wrap the power cord around the appliance.
• Always store the appliance and charger in low moisture area.
• Do not expose the appliance to temperatures over 140° F (60° C).
• Detach removable power cords from the appliance during storage.
• Do not use this shaver if the cutting head surfaces are damaged
or broken as skin injury could occur.
• This shaver and trimmer are intended for use on scalp hair only.
It should not be used for facial hair or longer hair on your body.
PRODUCT FEATURES
SHAVER PARTS
1. On/Off Switch
2. Shaving Head
3. Pop Up Trimmer (not shown)
4. 360° Pivoting Neck
5. LED Battery Indicators
6. Hair Pocket
7. Charging Pins
8. Power Adaptor
9. Head Guard
Also Includes (Not Shown):
• Cleaning Brush
• Shaver Lubricant
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
GUIDELINES
• Do not attempt to shave head hair that is longer than 4 days
growth or 2.0 mm. The Balder Head Shaver is intended to
maintain the shaved look and can be used daily or every two or
three days.
• The Balder Head Shaver cannot shave long hair down to the
shaved length. If your hair is longer than 2.0 mm you should trim
it down with a hair clipper first before using the head shaver.
• The Balder Head Shaver can be used dry or it can be used with
shaving cream or gel in the shower.
1. Hold the head shaver body in the palm of your hand. Press the
On/Off switch to turn the head shaver on.
2. Press the five cutting heads against your scalp. It is not
necessary to press hard to shave. Pressing hard does not cut
closer and could increase irritation. The cutting head will flex to
follow the contours of your head.
3. Move the shaver slowly around your head. You may use linear
strokes, or rotating motion, whichever you feel is most effective
picking up and cutting your hair.
4. Use a hand held mirror to check the back of your head to
confirm a complete and thorough shave. You may also use your
other hand to feel for complete and consistent cutting.
5. It is not recommended to use the head shaver for facial hair.
6. When finished turn the shaver off. Check for the red low charge
indication.
SHAVING YOUR HEAD CHARGING
Register Your New Product Today!
By registering your new Remington
®
product, you will receive special offers.
Register online at: RemingtonProducts.com
Power System Cordless
Initial Charge Time 4 Hours
Full Charge Time 4 Hours
Cordless Run Time Up to 50 Minutes
Indicators 2 LEDs (Low / Charging /
Full Charge)
Voltage Type Worldwide 100 - 240V
Waterproof Yes
Replacement Head and
Cutters
SPR-XR7000
Power System: Cordless - shaver can only be used when
disconnected from the charging adaptor. The shaver will not
run while it is charging.
To preserve the life of the battery: do not charge the battery
after each use. The best practice is to use the shaver until the
red low charge indicator appears and then recharge.
Indicators:
• Low Charge: Flashes red when the shaver needs to be
recharged.
• Charging: When plugged in, the charging indicator will light up
green.
• Full Charge: Green LED indicator will turn off.
Note: Some countries will require the use of a plug adaptor that
is not included with your shaver.
Before using, read the important safety instructions in this manual.
1. Ensure the product is switched off. Connect the shaver to the
adaptor
2. Connect to a power outlet and charge for 4 hours when using
for the first time. This first charge is important to the shaver’s
battery life.
3. When plugged in, the charging indicator will light up green.
4. When empty, the battery should be charged for 4 hours for a full
charge and will provide up to 50 minutes of shaving time.
5. To preserve the life of the battery do not charge the battery after
each use. Best practice is to use the shaver until the red low
charge indicator appears and then recharge.
Caution:
• Make sure the shaver and your hands are dry when charging
the shaver.
• Always charge the shaver in a cool, dry place.
2
6
1
7
5
3
4
To Next Page
Need help?
General
