EasyManuals Logo

Renson Fixscreen (F) Series User Manual

Default Icon
16 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #5 background imageLoading...
Page #5 background image
Fixscreen
®
(F)
5
Bedienungsanleitung und Garantiebestimmungen
User manual & warranty conditions
Mechanical
It is important only to use the system for its intended purpose.
Never stand on the system.
Always take care when opening the cap on the container.
Never put your hand in moving parts and never place fingers between
the profiles.
Maintain the system at regular intervals and use only original
replacement parts.
Clean the system regularly.
It is normal for a small crease to form in the fabric: do not tension the
fabric.
• Never attach additional components or accessories to this product.
Except for the specially by RENSON developed accessories
Electrical (if applicable)
Prevent electrocution during maintenance using a plug or circuit-
breaker close to the system (check there is no power to the device).
If you have an automatic system, the cassette should be fitted with a
lockable switch.
The motor may overheat if the system is operated multiple times in
succession. The thermal cut-out inside the system will make it
inoperable for a while (approx. 10 minutes).
Place the remote control out of reach of children.
Check the cables for damage at regular intervals.
Electrical components may only be modified with the permission of the
manufacturer.
If the motor cable is visible and installed outdoors, the cable needs to
be protected by conduit or trunking which is sun resistant.
EN
6 • Sicherheitsvorkehrungen • Safety
Mechanisch
Es ist wichtig, dass das System nur für die Funktionen eingesetzt wird,
für die es konzipiert ist.
Stellen Sie sich niemals auf das System.
Gehen Sie beim Öffnen der äußeren Kassettenabdeckung stets
vorsichtig vor.
Stecken Sie niemals Ihre Hande zwischen bewegenden Teilen oder
Fingern zwischen den profilen.
Pflegen und warten Sie das System in regelmäßigen Zeitabständen und
verwenden Sie beim Austausch von Teilen stets die Original-teile des
Herstellers.
Reinigen Sie das System in regelmäßigen Zeitabständen.
Eine geringe Faltenbildung gehört zu den Merkmalen des Tuches: Es ist
nicht zulässig, an dem Tuch zu ziehen.
Befestigen Sie ni zusätzliche Teile oder Zubehör an dieses Produkt, es
sei das spezifisch von RENSON entwickelte Zubehör.
Elektrisch (falls zutreffend)
Vermeiden Sie Elektrounfälle bei Wartungsarbeiten, indem Sie in
unmittelbarer Nähe des Systems einen entsprechenden Hinweis oder
einen Arbeitsschalter anbringen (das Gerät bei Kontrolltätigkeiten von
der Spannungsversorgung trennen).
Bei automatischer Betätigung muss der Hauptschaltkasten mit einem
Schalter mit Schlüsselschutz versehen werden.
Bei vielfacher Betätigung unmittelbar nacheinander kann der Motor
überhitzen. Der interne Thermoschutz setzt das System dann
vorübergehend (ca. 10 Minuten) außer Betrieb.
Platzen Sie die Fernbedienung aus Reichweite von Kindern.
Kontrollieren Sie die Verkabelung regelmäßig auf Beschädigung.
Änderungen am elektrischen Teil des Systems dürfen erst nach
Genehmigung durch den Hersteller erfolgen.
Falls bei Aussenanwendungen das Motorkabel sichtbar ist, muss dieses
Kabel mit einem UV-beständigen Schutzschlauch zusätzlich geschützt
werden.
DE
7 • Installation • Installation
Öffnen der Verpackung
Zum Schutz während der Lagerung und während des Transports wurde
das System mit einer Verpackung versehen.
- Die Lagerung muss stets in trockener Umgebung und unter normalen
Temperaturbedingungen erfolgen.
- Transport und Handhabung müssen mit der nötigen Sorgfalt erfolgen.
Kontrollieren Sie die Verpackung auf eventuelle grobe
Beschädigungen.
Öffnen Sie die Verpackung mit der nötigen Vorsicht.
- Achten Sie bei Benutzung scharfer Gegenstände darauf, den Lack
nicht zu beschädigen.
- Entnehmen Sie das System mit der nötigen Umsicht aus der
Verpackung.
Anbringung des Systems
Siehe Montageanweisungen.
Elektrischer Anschluss (falls zutreffend)
Siehe Dokument zur Einstellung des Motors.
Der Netzanschluss ist durch einen qualifizierten Elektriker gemäß den
geltenden Normen herzustellen.
Inbetriebnahme
Kontrollieren Sie, ob die nötigen Befestigungen den Montagehinweisen
entsprechen.
Kontrollieren Sie, ob die elektrischen Anschlüsse in Ordnung sind und
ob sich im System keine Kabel mitdrehen können (falls zutreffend).
Lassen Sie das Tuch einmal ab- und wieder aufrollen (falls nötig den
Elektromotor nachregeln).
DE
Opening the packaging
The system is packed to protect it during storage and transport.
- Always store in a dry place at normal temperature.
- Transport and handle the system carefully.
Check the packaging for signs of major damage.
Open the packaging carefully.
- If using sharp objects, be careful not to damage the paint.
- Remove the system carefully from the packaging.
Installing the system
See installation instructions.
Electrical connections (if applicable)
See motor installation document.
The mains connection should be made by a qualified electrician in
accordance with applicable standards.
Starting
Check that all items match the installation instructions.
Check that the electrical connections are in good condition and that no
cables can become entwined in the system (if applicable).
Roll the fabric up and down once (adjust the electric motor if
necessary).
EN

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Renson Fixscreen (F) Series and is the answer not in the manual?

Renson Fixscreen (F) Series Specifications

General IconGeneral
BrandRenson
ModelFixscreen (F) Series
CategoryProjection Screen
LanguageEnglish

Related product manuals